I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
I developed one project using BMD-300 Evaluation Kit that include nrf52832 microcontroller. In my project, I use the nRF5_SDK_14.2.0_17b948a and s132_nrf52_5.0.0_softdevice...
Hi everyone,
Using the SDK11.0.0 development product, it was found that the 52832 restarted randomly, with a reboot time of 7 days or longer.
App code condition:
1....
Hi guys!
First of all, sorry to make this question here because it is almost unrelated to Nordic, but I am desperate. I developed a device using your nRF52832. I programmed...
Hi,
I have a problem with Thread network stabilty and formation in new SDK for Thread and Zigbee 1.0. Examples seems to work fine in unchanged form, network is stable and...
Repetition of the steps followed here.
(1) Generated priv key, and public_key.c file using nrfutil, (2) generated the bootloader_settings file using nrfutil (3) Compiled...
hi!
nordic team
i am using thingy 52,and i meet a question that app_thingy_s132.axf: Error: L6405E: No .ANY selector matches accel_auto_cal.o(.bss) when i compile this...
Hello,
I am using nrf51822 with sdk11.0.0.
i observe that in while loop sd_app_evt_wait() function take much time for next interrupt to be pick.
is there any alternate...
I am developing a BLE anti-lost APP with community search, I set scan continuously or scan window 5 secs and scan interval 10 secs, but it drain phone's battery. How long...
Hi there,
I am working on having serial bootloader in nrf51422 to perform dfu over UART. DFU serial bootlaoder example in sdk11 claims to do the same.
After flashing...
I can't figure out why I can't send ADC values to the NUS service via BLE correctly. I should be getting hex values that convert to something like 0 or -1, since the ADC pin...
Hi all,
I'm currently learning on how to build bluetooth connections with a device from an app. For that I downloaded the iOS version of the nerf Toolbox app, as my chip...
hi
I am using nRF52 DK
Loaded Blinky Peripheral
I Connected this nRF DK to Com Port and Started Master Control Panel
But the Start Discovery Button is Disable. Please...
Hi,
I have an issue wherein once OTA update is complete through nRFToolbox (Toolbox says " Upload Complete") the Device does not reset and shows that it is connected to...
I am in the development stages of developing a ble application with the nrf52840 nordic chip.
I have come to realize the increasing difficulty of debugging this chip only...
