Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Can i use the nRF Toolbox app as a BLE peripheral and the nRF51-dk[PCA10028] as a central device.
Also,if not,then please suggest any other App that can be used for the same...
Hello,
I've downloaded nRF5_SDK_v11.x.x and install it, my keil version is v5.14. I flashed s130 v2.0.0 into nrf51DK, then build "ble_app_beacon" basing on SDK v11.0.0 and...
I use the S110-6.0.0 to find the iphone ANCS service,return attr missing. The 16bits UUID is xF431.I have added the long UUID ble_uuid128_t ans_base_uuid = {0xD0, 0x00, 0x2D...
Hi~
I used keil software environment for development.
Apply Ble UART example code from nordic keil example.
Example code down load to nRF51 Development Kit and run, program...
Hi, i need to calculate the frequency of two PWM.
When it comes to frequency calculation, the counter function is the best solution, i think.
i'm using SDK 6.0.0 for...
I want to develop an app that wakes app from sleep mode after pressing 2 buttons, then if these buttons are still pressed for 5 secondes i want to do an action ..
Any idea...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
Is there a call to read the stack ID.
For example S120 v2.1 has an ID of 0x006B . nRFgo studio is able to read and report this value.
Is there a way to read for me to...
I'm using SDK 11.0 and example\ble_central\ble_app_hrs_c
I have cut SB1 SB2 to disconnect the 32Khz crystal from the pca10028 and configured the example program to use...
Hi, When I write data synchronously to memory (nRF51822), I do :
APP_ERROR_CHECK(pstorage_block_identifier_get(flash_handler, 2, &block_handler));
APP_ERROR_CHECK(pstorage_clear...
Hi,
Im having a problem with connecting my phone to nrf DK.
im trying with apps from examples and they work well with HTC one, but my Samsung S6 fails to find device ...
I flashed dual bank ble bootloader from newest SDK (6.1.0) and used it to load my application to chip. I also modified my application (according to instruction here: devzone...
Hi, I have two device. S120 Scanner and S110 Peripheral Device.
At Scanner, I use SDK 9.0.0 and S130 1.0.0, At Peripheral Device, I use SDK 9.0.0 and S110 8.0.0 ..
Scanner...
hello,
I have a custom board which works fine with SoftDevice+Application , but if i Combine a boot loader hex that i complied it doesn't work. But the same ( bootloader...
I found and implemented an example that gives me a decent idea of how to go about polling for data with the UART/FIFO. However this doesn't give any indication of how to use...
