Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
I have asked if I can post this request, ticket number 354361.
Can you help with new research on secure boot?
I am a cyber security researcher at the University of Bristol...
Hi there
I have a question about the way the nRF52 radio handles on air addresses. I currently am developing custom software that uses the nRF52810 radio for a custom protocol...
I’m working with a Manufacturer-Specific Cluster (Attributes) in the Matter Template sample from NCS SDK v3.1.1, and it works fine with attributes. However, when I try to...
Hi, We designed a board using NRF5340-CLAA-R by following the Altium Reference design. Although when we tried to place an order with JLCPCB or PCBWAY, then informed that they...
Hi, I am pretty certain I have used RTTViewer before on the nRF9160, albeit not frequently. I cannot remember if I only used it on custom nRF9160 boards or if I used it on...
hello,
on our bm833 dev board, I scope (using a PIO) the time it takes for the bt_nus_send function to send 146 BYTES. The PIO goes to 0 after the callback nus_sent_cb has...
Summary
We are developing a Central application on the nRF7002 DK (nRF5340 SoC) using NCS v2.7.0 . The goal is to establish and maintain 11 concurrent Bluetooth Low Energy...
We're working on a project that interfaces an nRF9151 with a BQ40Z50 from Texas Instruments (via I²C / TWI / SMBus), and we've noticed the communication is unreliable. The...
Hi,
We are currently working on power optimization and want the device to wake up from the System ON state ( PM_STATE_SUSPEND_TO_IDLE ) using the RTC0 timer. However, I...
Trying to prototype a pinout on the nRF54L15 dev kit. We want P1.02 to be a GPIO pin instead of NFC. We followed the instructions to recover the device which erases the UICR...
Hi,
I am facing the following issue when i am calling west build from gitlab runner.
west: unknown command "build"; workspace C:\ncs\v2.5.0 does not define this extension...
Hi,
I am trying to come up with a different approach to SED reattachment using a backing off MLE session. Is there a way for the SED to keep on the polling even when in...
I'm working on an nRF9151 application that periodically sends small UDP packets (20-40 bytes) over both terrestrial LTE and satellite NTN networks. The device uses PSM between...
Hi,
We are doing some RF certification testing, EMC and also FCC, and wondered if you had advise on setting the modem on and transmitting, potentially if there is some...
Hi there. I have been working on a small project where I am using an encryption library for communication over ble. I am receiving encrypted token over ble charcteristics...
