Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi,
We use TLS encryption with MQTT towards Amazons MQTT-service.
What we have been able to do, is send 1 packet (2KB max size, due to modem buffer limit set by Nordic...
Hi
I'm currently trying to use a cheap stlinkv2 clone flashed with https://github.com/x893/CMSIS-DAP for at test setup. (cmsis-dap enables it to remove APPROTECT/read back...
Hi,I need Tune-Up Information for all chanels and frequency ranges( "source based time average conducted power") incl. production tolerances for Nordic NRF 24AP2 IC.to be...
Hi..... I'm working with custom service and characteristic!!! I succeeded in changing the characteristic length like bellow. attr_char_value.init_len = 10; attr_char_value...
Hi,
I am trying to do some tasks based on a particular button press, below attached is the buttons_init() function and the button_evt_handler() function. Code compiles and...
For the nRF52805 how is throughput specified?
Throughput Spec:
"It is capable of Bluetooth high-throughput 2 Mbps" ( ref )
Is this spec for serial throughput...
Hi,
I'm trying to periodically send sensor data to the AWS server and followed the documentation here to connect and send data to the server. I use these configurations...
Hi!
I've been trying out a tutorial about adding custom service and characteristics ( https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts...
Hello ,
I am having nrf52832 custom board.
In my project i need to use both CLOCK source ( Low frequency clock and High frequency clock source ).
Timer running on high...
Hello, Second time in here, thank you so much for all the support so far!
I'm developing a Beacon BLE, I wanna be able to send data over Advertising or Scan response. So...
I am trying to implement ble_app_interactive on nrf52840 as my application will require 2 uarts. I have started from the example application for the nrf58832 and created a...
in nRF52840, current consumption can be decreased by executing code from RAM instead of from flash. How is it possible to execute code from RAM? how to executing code from...
Hi, I have one nRF52840 DK and 2 nRF52840 dongles, i used the latest SDK17.0, programmed nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\ble_app_blinky\hex\ble_app_blinky_pca10059_s140...
MacOs on a macbook pro with LMP 9 (BLE 5.0 support) and a new DK2 board, SDK 16; no example built
and downloaded (SES) is discovered by the mac (same with an IPAD 2 pro...
Hi,
I need to read a digital signal with varying pulse widths (Min ~120µs) over ~30ms. Currently (nRF52832) I'm doing this using a timer interrupting every ~15µs and reading...
