Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Current I used nRF52840 Dongle to develop a Bluetooth PC Tool base on nrf_ble_driver_obj_sd_api_v5 which shared on https://github.com/NordicSemiconductor/pc-ble-driver/blob...
hi,
I am done with general vehicle diag code. now, i need to interface with kwp via uart in nrf9160 controller.
please, suggest some ideas.
Thanks in advance ...
I just bought nrf52840 and J-link V9.
I look at start nrf52840 blinky.
website:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0...
I want to read ADC values from AIN2 (P0.04), and AIN3 (P0.05) channels of nrf52805. I am using S112, and I have the following code found in the internet.
float readADC(uint8_t...
Hi,
I want to build up a test software to test our product.
I find out pc-ble-driver that might be conformed our requirement and follow up below link to set up environment...
Hello, everyone.
I am using sdk v17 and I am looking into timer. I used the app_timer simply, but I don't know the nrf_drv_timer because I've never seen it before. Can...
I am a beginner who just bought nrf52832 dk and started !!
I am trying to control the pressure sensor, gyro/ accelerationsensor and motor,
but i ts not easy because...
I'm trying to build a quick application to scan for all devices in the vicinity and print out their details (device name, manf data, RSSI, and BLE address). I am parsing the...
According to BLE 5.1 Core Specification Coded PHY and CTE are mutually exclusive. But losing 4xRange to implement Direction Finding is a big loss if, for instance, you need...
Hello,
I used the examples\peripheral\libuarte example to implement a driver for NBIoT DCE. I embedded the sample in my project and started debugging. Although the transmitter...
I got an error at pc = 0x104F0 (id = 1, pc = 66800, info = 0). My code is advertising and doing nothing else except a timer for the LED flashing, so I'm not sure what could...
HI
I am using the customized nRF52832 board with a temperature sensor connected via i2c .Firmware i merged the ble_app_uart and twi_sensor xample code. Here the RX AND SDA...
Hi everyone,
I've written a custom BLE service with two characteristics. I want to write more that one bytes to one of the characteristics and then to store the written...
Hello,
I'm working with nRF52840 and SDK v15.2.
I implemented an USB layer with CDC and MSC classes based on nRF examples. All seems to work fine. The USB Serial port...