I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hi.
I'm developing application that is needed to include UARTE Interrupt.
I can drive UART interrupt well(not UARTE), but UARTE is not working.
Here is my code...
Hi, I need to send data larger than 16 bytes on a characteristic. I see that the maximum number of bytes I can send using the indicate function is limited to 16 bytes.
...
I am working with:
NRF52840 boards
nRF Connect SDKwith Zephyr
On Ubuntu
Desired behaviour would be:
Establish connection with Codded PHY
After some time disconnect...
Hello,
I'm working on a firmware for a device that is created using ble proximity example. It is power constrain device and required a connection interval of 30 sec between...
Hi Great Nordic Support Teams:
Our client is developing their BLE products with 5340 , and they'd like to use NCS SDK 1.4.0.
They setting up the NCS environment with...
Hello. I have a issue about fstorage.
first, I using S332 SD and SDK 15.3.0 version and 52832.
Init flow is below:
Log enable -> SD enable -> SD BLE & ANT enable ->...
Hi,
SES is not including the extra cmake build options, i tried prefixing "--" as we do it in west build, note that it works west build "west build -b nrf9160_pca10090ns...
I am attempting to create a custom Buttonless DFU application by building on top of the default example from the SDK. Specifically, I am merging the Buttonless DFU app with...
Hello,
I am new to the BLE world. I have a nrf52 DK and using softdevice 7.0.1
I am trying to to flash the basic blinky example.
In debug mode everything is fine,...
Hi, I have a custom board with an nrf52840 onboard I was able to program the nrf52, but then I executed:
% nrfjprog --eraseall
and,
% nrfjprog --pinreset
and the JLink...
According to the Zephyr documentation here the way to implement an application-specific exception handler is to define k_sys_fatal_error_handler. When I try to do this I get...
Hi. I'm doing the firmware on the custom board.
This board turns on when the button is pressed through the power button circuit. And I created the reset function using NVIC_SystemReset...
Hello, I would like to develop a simple program that sends and receives UART communication through 2 boards.
The example used "examples\peripheral\serial\pca10056\blank...
Hi, all
I'm using nrf52832 pca10040, s132..
I want to send and receive data over Tx , Rx pin.. with my custom board, cm1106 model..
<<<<<< I've connected the two devices...
