Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hi,
Good day,
I am having trouble for enabling the SAADC module. I keep getting the following error.
Following is the sd_config.h code
Someone help me solve this...
Hi,
I have read that using the external 32MHz crystal is mandatory for proper BLE radio operation.
However, is there any internal clock that could be used instead of the...
Hi, I am trying the to create a mesh application using iOS nRFMESH SDK. I am able to provision the device but i am not able to get data from the getCompositionData method...
We are using nRF51822 in our custom board.
We just remain two pin ------ SCLK and SWDIO
Can we programming by STLink ?
what's the step?
1.using nrfgo studio to programming...
I tried setting the name as AT+NAME=LGS\r\n
When I send AT+NAME?\r\n, I do read back the new name, i.e. LGS.
However, the bluetooth host continues to see my device as...
Hello, I am using the sim card that comes with the Thingy91 in Sweden, it works well but every time I reflash the thingy with a new version of my application it takes several...
I went through each of the steps for upgrading the thingy91 modem firmware -> application firmware -> 52840 firmware but when I look at the lte link monitor it looks like...
Device: nRF52832, SD132v7.0.1, NRFSDK 16.0.0
Host: nRF52840 USB BLE dongle, pc-ble-driver-py 0.14.1, Python script, Linux
We're developing a device that's a BLE Peripheral...
Hi, I am looking for any suggestions on heart rate sensors i can use that would easily integrate with the nrf52832. I am looking to get a finalized output from the heart rate...
Hi I have a few questions about bluetooth 5.1 and the CTE packets that it transmits.
1. I know that there is a physical difference in the hardware of a Bluetooth 5.0 chip...
Hi,
I have nRF52840 dongle PCA10059. I want to use dongle as sniffer.
So how and what hex file and other thing i need to do ? To use dongle work as sniffer.
Hi,
I have been trying to get UART working properly on my custom board but also on nRF9160 DK. I'm using only UART_0.
With CONFIG_USE_AT_HOST and without any uart code...
tag v1.1.0 (have done west update) using SES 4.30c as suggested by nrf connect Compiled and flashed using SES modem firmware mfw_nrf9160_1.1.1 downloaded and updated the certificate...
