nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
I'm a little confused by the packet rate I'm getting on Gazell. Or rather I'm confused by the low number of 'timeouts' I'm seeing - I'd expect to see more, and would like...
Hi all,
in my custom board I'm using an NRF24L01+ as RF transceiver. The relevant part of schematic follow: (hi res => https://imgur.com/a/z4nQxXh )
The following...
The nRF905 chip can be setup to different payload length. 0-31 byte
Must RX and TX unit be setup to same payload length or can RX unit be setup to ex. 20 bytes and TX unit...
Hello.
There is a label on the back of the nRF9160DK.
I can find "HWID: FF:6A:B3:34:69:AC" on the label.
nRF connect can get the same string: " FF:6A:B3:34:69:AC " when...
I am trying eddystone example from SDK 15, its working fine but once I press the button to enable connecting and function nrf_ble_es_on_start_connectable_advertising(); is...
I want to use REG0 to supply 1.8v to external 4.7k pull-ups including when the system is off. Looking at the product specification REG0 can supply 1mA while in system off...
I have updated my repos to the latest commits on master for zephyr, mcuboot, nrf, and nrfxlib. I ran `
pip3 install -r scripts\requirements.txt
and I can open the asset_tracker...
hi, I'm working with NRF52832, DFU service is configured as secured. my question is : i'm trying to change dfu char a ct e ristic property to "ind i cation" by writing to...
Hello
I would like to test if provisioning over GATT Bearer still works with our application. Firstly I thought of using the serial example together with the PyACI, but...
Hardware: nRF52832
SDK 14.2
Segger Studio
Hello Sir or Madam,
We've made a new hardware variant of a previous design with an nRF52832 on much smaller form factor...
I use the QSPI(SDK15.2) of NRF52840 to read and write FLASH. Every time I open QSPI function, QSPI is closed after writing flash, but after close QSPI, there will be occasional...
Hi,
I want to capture data from TWI ADXL345 and send them by ble_nus_data_send() to mobile. Timing of data sending is done by application timer. My problem is that when...
Hi,
I tried to merge ble_app_multilink_central and ble_app_uart_c.
But, when I run the project It errors like below
I thougt the problem is the address of RAM_START...
