Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
I am using 3 axis LIS2D12H accelerometer interfaced with NRF51832 with SPI interface. The sensor has sampling rate from 1 HZ to 5.376 KHz which is happening at sensor only...
Please, share the firmware of the board nRF9160-DK PCA10090 version 0.8.5 , which is flashed into a new board. The firmware that I received using the instruction ( https:...
Hello,
I am using NRF52832(WLCSP package) and nRF5_SDK_15.2.0 for the product.
I also use IAR Embedded workbench 8.32.1 as IDE.
Few hundreds devices are assembled...
Hi,
I'm trying to figure out how to ping a specific IP Address from the nRF9160 via AT Commands. I can't seem to figure out how to do a simple ping to an internet server...
Hello! Board nRF9160-DK. Compiled and uploaded the project asset_trecker (merged.hex). The LTE Link monitor shows a cyclic reboot. LEDs do not blink. where is my mistake
Sorry,I want to know whate is the different between BLE_UUID_TYPE_BLE and BLE_UUID_TYPE_VENDOR_BEGIN, the Device name will become N/A when I use BLE_UUID_TYPE_VENDOR_BEGI...
Hi,
I'm studying the example about the nrf_crypto for implementing asymmetric encrypt and decrypt function.
The suggestion on the Dev_Zone is to use the share key to symmetric...
Hi,
Is there a possibility that the order of the responses can be different with respect to the order of the requests?
We check for the success status of the APIs sd_ble_gattc_read...
These two options in nrf_mesh_config_app are arbitrary for me if I don't understand how they should be sized.
From the documentation of the MESH SDK 3.2.0:
ACCESS_FLASH_PAGE_COUNT...
My app runs the following code, that is supposed to init the SoftDevice:
nrf_clock_lf_cfg_t clock_lf_cfg = { .source = NRF_CLOCK_LF_SRC_XTAL, .xtal_accuracy = NRF_CLOCK_LF_XTAL_ACCURACY_20_PPM...
Dear Nordic,
We have developed a product utilized the NFC readable/writable feature of NRF52832. We have tested it against some of the HTC, Sony, Samsung, and Google phones...
Hi,
I will add feature "installation codes".
I guess that security API do work.
At coordinator side, zb_secur_ic_add, zb_set_installcode_policy functions
At end device...
I am trying to implement nRF52 Light Switch Proxy Server in nRF52832 boards. Everything works fine on behalf of board and it prints the Device UUID as well. Although I can...
i'm using nRF mesh sdk v2.1.1 with 2 boards and 1 provisioner board. I have un-provisioned 1 board with the help of config_client_node_reset(). I want to know the procedure...
Hi,
In your Light switch example, there is a GPIOTE_IRQHandler() in simple_hal.c. Since I added the nrfx_gpiote module to the project, this is conflicting with the nrfx_gpiote_irq_handler...
