Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi there,
I have my system totally working now. I am looking to sell 1000-10000 units next year, so this is fantastic. I first want to say thank you to Nordic for all the...
I am experiencing a strange issue with the bootloader on my custom board in SDK 14.2.
Symptoms are that the board won't run until given an external kick - all it requires...
We make the project where we want to connect new device (currently designing on nRf52832) to existing system made on nRF24. It's a beacon in proprietary mode. It should periodicaly...
I have a question related to memory protection and configuration of device in relevance to soft device.
nrf52832, sdk15, soft device S132
Question 1 : How can I be sure...
In datasheet it had been mentioned that in SPIM0,SPIM1,SPIM2 the SPI clock frequency should not exceed more that 8 Mhz. And SPIM3 nothing is mentioned. Can we understand that...
Hi, I tried to use pc-ble-driver-py script to talk to a nRF52840 DK. It works perfectly with the official connectivity app hex file (the one nRF-Connect PC application loads...
I modified the nRF5 SDK 15.1 example program serial to display a message on a physical device. I added a blinky service to the ble_app_template example program and I am able...
Hi, thank you for looking at my post.
I am using Keil V5.25.2.0 with a nRF51422. I am using the soft device "s310_nrf51422_1.0.0-2.alpha_softdevice." My memory regions for...
So, currently I utilize DK's to program and debug both pca10040 and pca10056 utilizing a custom shield that plugs into any of the nRF52 DKs. The programming and the debugging...
I used SDK15 and ble_app_uart_c.
I start a UART timer sending and start a LED timer. There is a probability of app: SOFTDEVICE: ASSERTION FAILED in the process of running...
Hello all,
I'm using the Nordic SDK 14.2 BSP button handler. I have a push, release, and long push event on a single button. These are working as expected -
Except when...
Hi all
I am using the spi0 to storage the data and twi0 to get sensor data . But after I add the file nrf_drv_twi.c and compile , it complies wrong :.
\_build\nrf51422_xxac...
I have problems with disconnecting my Android devices from my BLE peripheral. I don't think this is Nordic-specific, but perhaps someone has an idea?
Disconnecting using...
Hello,
i have a application with two operating states state1: device is in deep sleep state 2: device is running
i wake up the device from deep sleep via gpio interrupt...
Hi
I am integrating your Android DFU library with our mobile app to do FOTA to our Nordic device nRF52832 . We are using SDK 14.2 and doing the firmware update using zip...
