Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Dear developers,
We had a working application with SDK11 SD2.0.1 that we have migrated to SDK12 SD3.0.0. With SDK11 we could successfully bond to multiple peripherals and...
Hi. I use the nRF51882 and Arduino ide for developing. My main goal is turn on and off the Led thru the Bluetooth interface. But when I use the UART service for it I have...
I am seemingly haunted by spurious 'soft resets' I cannot seem to find a good explanation.
I have an application that is to be dormant until activated. When waking up I...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
Hi, Nordic
I download SDK13.0.0-1.alpha_055eef3, open project
\gzll\experimental\gzp_dynamic_pairing\device\pca10040\blank\arm5_no_packs\gzll_dynamic_pairing_device_pca10040...
Is there any example of changing the default mtu size of 23 to a bigger value?
We tried increasing the att_mtu to 512, and reserved more ram for the softdevice, but still...
I have a rather unique problem. I want to control an "old-fashioned" DPDT relay using nRF52 GPIO lines. I'm trying to accomplish this task without adding a power transistor...
Hi all,
there is a nice section in here already about enabling the Reset input (P0.21). Unfortunately the link to the relevant infocenter docu is missing.
Could you...
I think that all of the Experimental is all unreliable.
I try it 5 days to test it, It always Failure.
So , I want to know that to how to understand the keyword "Experimental...
Hello developers,
I am struggling badly to use interrupt in my application. I am using softdevice S130 and ble_nus, ble_bas and ble_hrm services. All I want is to trigger...
I would like to update my current bootloader with one, that is bigger than the predefined space of the current bootloader. For that, I want to flash an application via DFU...
currently(sdk_12.1.0_0d23e2a, s132_nrf52_3.0.0_softdevice), nrf52832 can't pairing with windows 10.1607(build 14393.479), if we set lesc bit in ble_gap_sec_params_t.
windows...
Does any one has successed in doing DFU with OpenMesh? I have done all the steps according to the guide ( github.com/.../dfu_quick_start.adoc) but failed in the last step...
