Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I want to use the nrf51822 to communicate withe the old module of 24l01p, in the module of 24l01p, the Address is
addrofch[0] = 0xe7;
addrofch[1] = 0x7e;
addrofch...
Hello,
I've been trying to get my TWI device working in conjunction with the BLE stack (i.e. s110 softdevice is enabled) on a nRF51822.
I found another thread with an...
Hi,
I want to use the 51822 to receive data that from the module of 24l01.the Address is
addrofch[0] = 0xe7;
addrofch[1] = 0x7e;
addrofch[2] = 0xe3;
addrofch[3] =...
Hi,
Can any one tell me, what will be the current taken by internal flash of Nordic for
write and read operation and what will be the max time nordic will take to write...
Can someone familiar with the nRF51822 timer infrastructure confirm for me what the maximum achievable PWM frequency is, assuming 8-bit resolution? I've been weeding through...
We got the new sdk and ported the "Alert Notification Profile" to the EVM board. It can communicate with the the Master Control Panel. We want to know whether it can communicate...
hello, on my board the nrf24l01 is optional.
what is the preferred solution to identify if a nrf24l01 is present.
I tried to read the status register. But sometimes...
I am using Laird Bluetooth-4 device BL600 with smartBASIC. While communicating over the I2C bus I am encountering the Hard Pull-up on SDA line. During the Slave ACK I could...
The new pstorage abstraction is almost using 1K RAM, which I'd actually planned to use for something else :-)
Is it possible to limit the RAM used by this module. Can I...
Hi there
can I download the source code?
This app is able to detect the nrf51822 chip even with android 4.1, which is great, so I could test my firmware on my samung...
Hi,
We have a custom board with nRF51822 chipset, We have developed the code to work with some senor peripherals, everything is working fine, but sometimes, when we do testing...
Hi:
chip:nRF51822
code:ble keyboard
How to send the VIRTUAL_CABLE_UNPLUG request by Bluetooth HID devices?
If Virtual Cable Unplug is received by a Bluetooth HID device...
hello，
the datasheet of nRF2460 “nRF2460_Product_Specification_v1.0” has a explanation “the MCLK signal on the ATX side is locked to the
reference （crystal）of the ARX...
