Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello,
I am scheduling an RSSI measurement operation using DECT PHY firmware v1.0.0. The parameters used for scheduling the operation are: - start_time = 0 - carrier = 1677...
We have a custom nRF9160 board in a dedicated directory (out-of-tree board). It is a near copy of the nrf9160dk_nrf9160 folder with hardware changes and additions.We are now...
If there have a peripheral sample support for multiple central?
How NCS realize saving bonding information and distinguish different devices that bond with my board?
Whether...
Here is my code: My issue is I am trying to get logging to happen over USB using the cdc acm with the Particle XENON board. https://docs.particle.io/reference/discontinued...
Dear all,
during the developing stage sometime the PROBLEMS panel show erros that are not real so a first question is what can be do to give such panel updated with the...
Hi.
i base on web address :
step then try to Read/Write UICR with nRF52840 , but can;t found DT_CHOSEN_ZEPHYR_FLASH_CONTROLLER_LABEL in code ,
Could you tell me How...
So basically, I am have created a key pair using the Identity key generation example and exported the public key using Identity key usage example. Now i need to create a certificate...
Hi,
I'm trying to set up nRF Connect Toolchain and SDK manually using west, but I've encountered the following error:
Before encountering this error, I tried to install...
Hi there,
This is actually a question re. the Android BLE library ( https://github.com/NordicSemiconductor/Android-BLE-Library ), so please re-direct me if necessary.
...
Hi all,
maybe a dumb question, but here to listen any advice. I am using nus to receive data from a phone, packets are in chuncks of 256 bytes, which is the "most used"...
When I flash the card and run it, I encounter the screenshot I shared in the attachment. The error "Modem has crashed, reason 0xfff, PC:0x0" occurs. Can't I send messages...
Hi.
We are using nRF52833 (on BL653 module) where UART0 and UART1 are used for communication purposes (one with STM MUC and the other with quectel modem). Current solution...
I'm working on a personal project and have designed and printed a small prototype board containing an nrf52810, external antenna, couple of crystals, and a ws2812b onboard...
Hi,
We are developing a mesh network. Our requirement is the one device can connect to three other devices. Using one connection as a peripheral and up to two connections...
