Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello,
I have recently been working on other Zephyr projects that use non-Nordic MCUs. I installed raw Zephyr in my documents folder (“C:\Users\gilles.devillers.SECTRONIC...
Dear DevZone,
We've encountered yet another Wi-Fi related issue after upgrading from SDK version 2.6.1 to 2.9.1. Our code is based on your HTTPS client. When calling connect...
Hi,
I am trying to integrate Sensirion SHT40 sensor with nRF52840. I am using the sensor sample app from 2.9.0 SDK. I am building with 2.6.1 SDK with toolchain 2.6.1. The...
While collecting 2-byte samples via SPI4 (with a 32 MHz clock) using PPI and timers—one triggering transfers at 400 kHz and another handling an interrupt every 512 samples...
Hi, Im setting up a project for custom board based on NRF54L15. I followed a tutorial on creating custom board and it works fine. Now i want to add BLE functionality similiar...
I am attempting to increase the MTU size on s132 3.0.0 and need to increase the available SoftDevice RAM unproportionally.
For every MTU byte I need to give dozens of bytes...
my minimal main() does the following, after coming out of reset with the MCU in its default state:
NRF_P1_S->DIRSET = 1; // LED0 output NRF_P1_S->OUTSET = 1l // LED0 on...
Hi Support Team,
I want to use an external flash(2M byte) to store the sensor data in a 'circular overwrite' way. I now tried it with the FCB(Flash Circular Buffer) on nRF5340...
I am currently reviewing Zigbee for an upcoming project using the nRF5340DK board. The build environment is nRF Connect for VS Code Extension Pack, and I’m using SDK version...
Hello,
I've developed a PCB that connects an RTD (PT100) to a Wheatstone bridge, set to 100 ohms at 0°C. The bridge terminals (as seen in the diagram) connect to AIN4 and...
Hi everyone,
I am experiencing an issue with my custom board configuration for the nRF9151. When using the same code that works with the nRF9151 DK configuration, I encounter...
Hi there!
May I know how to have UART00 on P2 like what is shown below as I wanted to have higher speed.
Is it the same as other UART assignments on P0 and P1?
Thanks...
I am using VSCode with the nRF Connect extension (latest) and SDK 2.9.1.
I made my new app from the Bluetooth Peripheral sample.
When I try to debug I get the following...
I am using VSCode with nRF Connect extension with the 2.9.1 SDK.
I am trying to write my own device driver for the Zephyr OS and the TI CC1101 chip. Since the tutorial isn...
