Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
Hey!
I'm working on a Firmware for a BLE peripheral device, I'm using the SDK version 17.1.x and the SD140 on a nRF52840. So far everything worked fine, I was able to...
Hi,
I'm trying to put my nRF52840 in System OFF and wake it up by DETECT signal on GPIO. For that I use gpio_pin_configure() with GPIO_INPUT | GPIO_INT_HIGH_1 flags but...
Hi i am involved in sdk5 based uart porting project
i can run example project and receive/send data to/from nrf52840-dk .
the problem is when i dig deep into the project...
Hi,
I am using a nRF52840 and SDK 15.2, and Soft Device S140 (BLE), where the device is battery powered.
In certain modes, the device sleeps to System Off mode, and...
I am currently porting the nrf_cc3xx_platform library to use it with RIOT OS . Following what has been done for Zephyr and FreeRTOS, I implemented:
Abort API
nrf_cc3xx_platform_abort_init...
Hello, I am working with the asset tracker v2 application and I want to connect it with Aws Cloud. I follow the steps corresponding to the tutorial and I am not successful...
I am trying to use the pc-ble-driver and as a first step want to use the heart_rate_collector example. I downloaded the source as follows:
I then followed the instructions...
Hi everyone,
I have an nRF52832 embedded as part of a dual chip (connected via SPI) and I'm looking to reduce the sleep current as much as possible. I'm currently measuring...
Hi, On both nrf52840 DK and Dongle, the sticker shows 4 info: - PCA board ID - version - year.month - Serial Number/MAC Address Could you please clarify what the last value...
Dear Nordic Community I am trying to get the nrfx adc driver to work with zephyr ( link ). With the help of this post , I ended up with the following code:
prj.conf -> ...
Dear Member,
I want to add ADC the main code,
but I got :
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol nrf_drv_ppi_init (referred from adc.o).
I'm using...
Hi, I am not sure whether there is I2C pins on nRF52840 Dongle board as based on the Adafruit Feather nRF52840 Express the pin is P0.11 and P0.12 as shown below: SCL 0.11...
Hello I am learning how to connect timers with gpio via PPI, i working on nrf52832dk.
So far I have connected the RTC 0 alarm channel to the LED no.3 (pin no.19) and its...
Hi, I am Shuang. I am now working on the Bluetooth direction finding function, but I have some problems, and I hope I can get your help.
I have experimented with Bluetooth...
