Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hi,
We're evaluating NFC for our project.
I've been testing with a nRF52840DK - PCA10056 Version 3.0.2.
Using the antenna supplied with the Development Kit I am...
Hello support team,
where can I find a simple NCS V3.x.x example in which the central and peripheral are implemented in one device (e.g., nRF54L15)?
Thank you in advance...
Hi,
I have a simple question about Bluetooth Channel Sounding:
Question: If I use BT_CONN_LE_CS_MAIN_MODE_3 as main mode (PBR + RTT), does it make sense to use sub mode...
nRF NCS 3.0.x
Target : nrf5340dk or native_sim
What is the latest recommendation on build environment (assuming preference is a docker image for consistency of build...
Hello, I am having a problem using the Segger IDE. I am using the nRF52-DK and got my SDK download from the following link, nRF5 SDK - nordicsemi.com .
What I did exactly...
Hi,
The URL below does not have the DNs number for v2.9.2, but is it the same as for v2.9.0 and v2.9.1?
https://docs.nordicsemi.com/bundle/comp_matrix_nrf54l15/page/COMP...
I am using the VSCode. After building the project , I want to view the warnings. However, when I click the error message but it will show that the editor could not be found...
Hello, I hope you are well.
I created a new driver for an i2c accelerometer with 2 gpio interrupts, but it does not build properly. When calling `static const struct device...
DPPI is not able to build with SDK 2.8.
The issue seems to be the NRF54L15 has 4 DPPI peripherals, yet the NRFX hal version 2.8 only works with one.
Would it be...
Hello everyone,
I'm working in a ble project that use uart interface. When I sent string data in nrf connect app, the uart_event_handle is not called.
I started my project...
Hi everyone,
I currently installed the latest version of the NRF connect SDK. I started a new build task which executes properly. The task doesn't however stop.
This...
Hello,
I am working on a hardware design with two MEMS PDM microphones and a mono speaker. I think I have the peripherals allocated and wired correctly but wanted to run...
Hello,
I am testing a simple BLE application running in two different boards: nRF5340-DK and Fanstel BC40M. First test without MCU Boot, second test with MCU Boot. Same...
Hello everyone,
I'm using the ble_app_uart example code in my MDBT50Q-U512k. I have been made some modifications according to my application. I need use fixed value pin...
