I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Currently I am trying to add uart functionality to the dimming client from the mesh dimming example, but I just can never seem to get it to compile. I can confirm my uart...
I work with Zephyr v1.5.1. PDK NRF5340. I implemented interrupt from PB1 and sometimes I get double interrupt. 1. Is input Debouncing supported in Zephyr?
2. How can I implement...
HW- nrF52832
SDK- nRF5_SDK_15.2.0_9412b96
Description:-
I am using a nRF52832 for my project development. Flashing first time with softdevice and my application hex...
Excuse me:
The SPIS example in SDK is shown in the figure below,the m_rx_buf buffer has only seven bytes，Does NRF_DRV_SPIS_XFER_DONE event occur when the buffer is full...
I am developing a NRF52810 product, I am downloading using JTAK on NRF52832 development board.
I have the NRF52810 because of the lack of IO pins. SPI CLK , TWI CLK are...
I use the NRF Mesh SDK v2.2.0
- EVB PCA10040 burn the serial example
- EVB PCA10056 burn the light server example
- PCA10040 attach to the Raspberry Pi 3 via USB for...
I'm trying to follow these instructions to update the openthread binaries in nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8.
I have a Windows host machine and a Ubuntu VM...
Hi,
I am trying to do AGPS with the supl library. I obtained version 0.7 through the application and installed it (and enabled the required config options).
Unfortunately...
Hi Nordic,
I am working on project with nrf52840 , which is a central to connect other device. we will enter the MAC address to central, and setup the scaning filter.
...
Hi all,
I am trying to do bonded buttonless DFU but an error named NRF_ERROR_FORBIDDEN was raised in enter_bootloader() function under ble_dfu_bonded.c.
The description...
hi，
I currently have an application scenario，using a nRF52832(M board) BLE maser to upgrade another nRF52832(S board) is run standard DFU ，Are there any demo available？
Previously, I used SEGGER to build and run programs on nRF52 DK very quickly (5-20 seconds).
However, for nRF5340 DK, it usually takes about 8-15 min to build and run just...
