We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
https://www.nordicsemi.com/Software-and-tools/Development-Tools/nRF-Sniffer-for-Bluetooth-LE/Download#infotabs , I have used this link to access the nrf sniffer hex...
I'm struggling to understand the difference between nrf_pwr_mgmt_run() and sd_app_evt_wait(). When should I use each one? It looks like nrf_pwr_mgmt_run() calls sd_app_evt_wait...
ok I am using nrf52820 and sdk nRF5_SDK_17.0.2_d674dde
when i was using
ble_app_uart\pca10100e\s112
Its work correctly
and
the dfu
pca10100e_s112_ble
also...
I am having problems advertising both FOTA and a custom service. I started with the peripheral sample (zephyr\samples\bluetooth\peripheral) and the smp_svr sample (\zephyr...
A SoftDevice is software which implements a wireless protocol and the nRF51 and nRF52 series specifically mention them. Since the nRF5340 has a dedicated network processor...
Hello,
I'm coming to you with a beginner question, I would like to use the functions localtime, difftime, strftime but I saw that time.h is not included. Is it possible...
The test of I2C signal found that the logic low level could not be lowered. It was pulled up to 3.3V through the external 1K resistor, and the logic low level of I2C was about...
I'm getting strange behavior when connecting to nRF52840DK.
Log from nRF:
Log from android nRF Connect:
The same code works on our custom board (nrf52832). We use...
Hi Nordic DevTeam,
So I already followed this tutorial on how to add custom service UUID.
https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial
I have...
We are using softdevice S140 6.1.1 with nrf52840 for a BLE peripheral. We see that mobile devices are not able to discover this peripheral intermittently for some time during...
Hello, there
We are using a custom board to upload data via udp connection. The send() call not return sometime, and the main thread is blocked as a result
Modem firmware...
Hello,
We are using a passkey in our application and by default is 6 digits long. I have found in other posts that this is mandatory a cannot be changed.
Is it real...
Hello,
I am using NRF52840 with SDK 16.0.0.
We have to detect reed switch pulses coming from a water meter. We use app_button as it provides debouncing inbuilt.
Pulses...
Dear sir,
I want to know about co processor with details of nrf52840 , and is there like dual core processor like another processor.
Note: and need more detail about...
Hi,
I working on a BLE app with 2 custom services.
When I try to expand a characteristic I get a spinning indicator below the characteristic and after a while I get...
