Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I'm trying to run Provisioner Example on my nrf52840 DK, which is in examples/provisioner directory, . First I've build softdevice on DK and then I'm trying to build provisioner...
Hey NordicSemi. In my new project, I use DK NRF9160 and I need to determine the location. Since hardware GPS does not work, I decided to use the detection of coordinates through...
Hi,
Something locks-up my I2C sometimes and I need to make I2C recovery. It looks like Nordic has not implemented the zephyr i2c_recover_bus function, so I guess I need...
I'm looking for dual core inter task communication examples
where a thread on one core is interacting with a thread on the other core ?
e.g. will there be some kind of...
Hello All,
I was looking at the Digi XBee3 modules for a ZigBee project I am working on. What is great is they allow you to write MicroPython code to control the network...
I am trying to send some values from nRF52810 Board to my Laptop. I am using a nRF52840 Bluetooth Dongle to connect the board to my laptop. I am using the "Heart Rate Collector...
Is there a way to get the values of CompanyID ProductID & VersionID before provisioning? I'm working on my android application using the nRF Mesh Library and after identification...
Hello, I work on nrf9160 dk and i try to get tx power: For exemple, with a RSRP -76 dbm i get this consommation curve (read current on P24 throught 0.5ohms resistor):
and...
Hello,
we are developing a HID slave device. we need to support five cell phones connect and bond with the device not at the same time.
we use the ble_hid_keyboard example...
Hi,
I am check this code: https://github.com/NistantriTech/ibeacon_nrf52/tree/ed938973c9a8ebd4f0bb91a3689e5d8242980681
It used SDK15.0
On Ebyte 52832 - and face problems...
Hi
After trying out nRF5340 step-by-step guide we'd like to learn nRF52833 following similar step-by-step start-up guidance if such exists.
I guess for the basic operation...
Hi all. I am using the twi_sensor example of the sdk12.3 in a NRF51822 Taking a look on the tx function: err_code = nrf_drv_twi_tx(&m_twi, MXC400_ADDR, reg, sizeof(reg), false...
Hello ,
we know that, when initialize a BLE slave device ,we need to define the BLE MAC address type.(we need to write our owen address ,not usig the original ble address...
