I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hi,
I'm using NRF52840 with direct test mode application.
I'm sending to the function dtm_cmd following parameters: 0x4000, 0x8000, 0x9400, 0xA500.
I understand...
Hi,
After suspending task in a specific code line (using vTaskSuspend) and resuming the task (using vTaskResume)- will the task continue from the specific suspension line...
I am going to make a project with nRF52840 In my application, I need to send sensor data to Raspberry Pi I noticed this tutorial and tried to implement this in my project...
i tried to implement radio notification in order to change advertising data but i had this error
when i put the periority to LOW i get this error, if put MID or HIGH the...
What benefit is there to RX gain for the bluetooth front end module
Most other 2.4 amplifiers do not have RX gain.
Our concern is the noise floor, would not the RX gain...
Hi Sri,
When referring to this ink , we know the typical and max ripple values are 70 mV and 100 mV respectively at REGOUT0=1.8V.
Two questions:
1. Do we have the...
I am attempting to add peer manager bonding and whitelisting to an existing app.
The app is simple, uses nordic uart services to pass 4 bytes of data between two embedded...
I am currently using nus and dfus service. It works fine. The secure DFU service is displayed in the nrfconnect app.
However, when ble_bas_enable, the duf service disappears...
Hi,
Is is possible to use printf while using the libuarte library? I am trying to link the nrf_libuarte_async_tx() function to printf but I am unable to make it work....
Hi there,
I'm using nrf52840 DK and Custom board, SDK 17.0.2, Segger Embedded Studio(SES v5.20
my issue is when we send/TX data through UART "static uint8_t text[] = ...
Is it a good/bad idea to put capacitance on the nRST line. I noticed the nrf52840 DK does not have any capacitance on the nRST line. At least none that I can find, tracing...
Hello,
I have a nRF52833 on a nRF52833-DK or the PCA10100 and want to do development but I have found several projects don't have a Segger Embedded Studio project (for the...
Hello,
I just installed nrfutil with
pip3 install nrfutil
All the requirements are met:
andreas@notebook-fh:~/github/pc-nrfutil$ pip3 install nrfutil Requirement already...
