I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
I am currently developing my app with nRF52 DK and use the nRF52480 Dongle as a simulated sensor using the built-in server definition capabilities in nRF Connect for Desktop...
Hi.
I am looking for advice on which board may fit my purpose. My intended route as of right now is described at the bottom of this post. I have a door lock that has an...
Hi, I am using ANT Protocol in nRF52832 SES SDK17.0.2
Run the code in <Install folder>\examples\ant\ant_broadcast\tx file and i found that need to download the SDK file...
Hello I have an application which advertises permanently on the Bluetooth but I would like that under certain conditions, that they advertise another name. Can you tell me...
Hi everyone,
In the USBD example we use ENDPOINT IN 1 to comunicate (if a button is pressed) with the host the position of a mouse.
I modified this example, I don't need...
Dear Sir.
In my program 2 strings I need to protect when a new firmware is updated.
#define PROD_DATE "PROD_DATE_03_12-2020" #define IRON_NUMBER "IRON_1234567899999...
Hello,
In my application I use NRF52840 with SDK 16.0.0 and softdevice 7.0.1. I want to add ECDH algorithm to my project using ECDH example in the SDK, but nrf_crypto_ecc_key_pair_generate...
Hi there,
I'm presuming that, when using the s140 soft device (or any of the soft devices), I cannot change the output of VDD to anything and must assume 3V.
I have tried...
PWM frequency and PWM steps resolution are related, we increase one and the other decrease and vice versa, we want high PWM frequency so we have low flickering and we want...
Hi everyone, after months of working with the nRF52840 dongle I decided to buy the nRF52840 DK. I work with the ide SEGGER EMBEDDED STUDIO. I tried to get the blinky example...
Hello,
I can smoothly run the sensor server / client model. I know that I can setup the periodic publication period with the nRF Mesh mobile app and don't have a problem...
I want to configure 32bytes sensor measurement data in advertise manufacturer specific data as follows.
But does not work, please help me.
My environment as follows. ...
Is there demo for video transmission on PCA10056 DK?
it is just video transimission demo. just loopback is ok.
we are using nRF52840. is it possible？ or other platform...
Dear Mr/Mrs,
I am learning to develop an Android BLE apk. I use the nRF Connect apk and Android-nRF-Toolbox to connect with my BLE device.
nRF Connect connect to the BLE...
I have an found a problem where I find FDS has 2 pages labeled as swap, which results in loss of one of the data pages.
my configuration is 2 data pages and 1 swap page...
