Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I am new to nordic ble chips.
I am using nrf52832 ble chip, s132_nrf52_3.0.0_softdevice
I am trying to update firmware on the air. But I am getting an error that I do not...
Hey,
Up until now I have only been dealing with software. Now however, I want to create a device that I can use to track my bike by GPS and heading. In the future, I want...
Hi
I am having a problem now(maybe a bug).I refer to nest_state.c and access.c build my user_flash.
But some time,when I reset device,write data to flah will be fail....
Hi,
I'm using the nrf52840 with sdk v15.3 and I'm trying to list of the characteristics of a specific service that has a 128 bit uuid running on a peripheral. However, even...
Hello,
I would like to be clear on the pros/cons of registering a new SIG-adopted UUID versus a vendor-specific UUID. We are a small developer and the cost of registering...
Hello,
I have two differents sensors on one SPI port and I don't really know how to be able to use both. Of course all are connected in the same MISO/MOSI/SCK but there...
Hello,
We currently have several devices out in the field as test units, installed at beta sites. The new modem firmware v1.1 has several features/fixes that we want to...
Hi, we are working on custom board using nRF52811 SOC, I have some confusion
1. regarding the antenna design, I copied the Antenna from Dev board, but it is designed for...
Hello,
There's an interest on the LTE-MTC module.
I can see it's based on nRF9160.
I'd like to inquire about the MTC technology please, does this module support CATM2...
Hi,
I'm using a buffer size of 64 bytes using function
nrf_drv_uart_rx(&app_uart_inst, rx_buffer, 64);
When I receive only one byte packet from the remote, I get EVENT_RXDRDY...
i want to use pwm of rnf52810.but i don't know how to recognize what pins is pwm.
what pins in 52810 i can use wire to connect and then use it's pwm function?
or i can...
Hello, I try to import big project from Keil to SES. The main idea is to move to better IDE and use the same compiler ARMCC provided by Keil (license is present).
I have...
I am trying to using ceedling with FFF to create mocks of some of the NRFX HAL files. However, when I run ceedling I get some very weird errors. I've taken the `test/include...
Hello,
Below are details of my setup:
Peripheral: nRF52 DK
Central: One Plus 5 android phone
Sniffer hardware: nRF52 DK
Wireshark version 2.4.2
On Wireshark, I...
Hello everyone,
Some info about my setup: OS: Windows 10 IDE: SEGGER Embedded Studio v4.22 (64bit) HW: nRF52840 Dongle rev 1.2.0 as Coordinator, nRF52840 DK rev 1.1.0 as...
