Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello All,
I am working on the NRF51822 custom board.
I am Using the SDK 12.3 with s130 (PCA10028)
1.) Is it right sdk for nrf51822..?
2.) Facing issue in configuration...
Hello,
I am working on a beaconing application and I was wondering if it is possible to run the code beginning with system off mode and wake up the board with a button press...
Hi,
we are using a sensor which streams out buffered data to an ios or android app. If we face a disconnection the data gets buffered and send when reconnected.
But the...
Hi,
I am using customized nrf52 board with softdevice s132
I am trying to interface External Flash (MX25L64) using spi.so when ever i am trying to send any command /data...
Hi
I figured out, that the macros in nrf_esb_resources.h are wrong.
You can find the used resources (PPI, TIMER and SWI) of the ESB library in Enhanced ShockBurst...
What is the operating and storage temperature range of nRF52840-DK development kit and USB dongle? We need to use these evaluation boards at a temperature range of -20 to...
Experts,
I'm trying to use NRF52480 Dongle to communicate over UART serial port. On the forum I found that pins 1.10 & 1.13 are used for TX/RX. I learned that flow control...
If i buy a raw nRF52832 chip and design the circuit by myself, how can i pre-programm the serial bootloader in it? So i could use the FTDI Basic (or an FTDI Basic -like device...
Hi,
Is there any way to change the advertisement name before switching to DFU mode?
I have a custom app that reboots into DFU mode (via NRF_POWER -> GPREGRET ). I want...
Hi,
I've to design an alimentation with capacitors to keep energy and filter current peak. To do that I need to know timing for NFC peak current. Do someone have information...
Hello,
I have a running system constituted of a central and 15 peripherals using nRF52840 devices. The central is set to scan the peripherals for 5 seconds then stop and...
Hello,
I'm implementing a beacon scanner with nRF52 using nrf_ble_scan.c. After the scan has been configured with no filters, no advertisement reports are returned to the...
Hi,
The definition of the COEX1 pin looks to be really interesting for applications that need a reliable time reference. A 1PPS GPS output is very useful; absolute accuracy...
Hi
Our nRF9160DK card seems to have stopped working. We attached a sensor to the card (We might have connected the reset pin on the P7 strip) and now I can't start any program...
I was trying to make sense of the serial support in mcuboot, but it uses a protocol and format I don't recognize. I expect they're generated by the Apache Newt tools, since...
