Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I am trying to enable the Channel Sounding feature on the nRF54L15 DK by sending HCI commands over a "USB to UART" interface. For this purpose, I created the "hci_uart" sample...
Saw this post from about 1 year ago.
Any updates regarding USB host firmware support on the nRF54LM20 or any timeline for when it is expected to gain some level of support...
Hi,
I'm developing a Channel Sounding application on nRF54L15 and trying to understand how the different TX power settings interact.
I have a few questions:
What does...
DevZone Post: Custom nRF54L15 Board Not Recognized by Kconfig (Falls Back to Apollo4X)
Summary: I am bringing up a custom board based on the Raytac AN54L15Q (nRF54L15)....
Hello
When following the guidline of a new way to extend boards , VSCode "Add Build Configuration" is blank. Am I doing something wrong or this is not yet supported by...
HI
I’m currently using NCS 3.2.1 , working with the periodic_adv_conn sample.
On the advertiser side, after receiving data from a node during each periodic sync broadcast...
Environment
nRF9151DK.
Using nRF tools and SDK v3.1.1 & also v3.2.3.
Based in New Zealand and currently on Spark network.
Issue
Trying to run the sample app...
Good day,
We are developing a board with a nRF54L15 + nRF7002 for BLE and WiFi connectivity.
The Nordic nRF54L15 + nRF7002 reference design has been a good starting point...
I see this errata: https://docs.nordicsemi.com/bundle/errata_nRF54L15_Rev2/page/ERR/nRF54L15/Rev2/latest/anomaly_L15_24.html#anomaly_L15_24
It says this:
"Symptoms ...
Hi, in order to be familiarized with the transceiver we have purchased an evk nRF9151 from Nordic.
I have some questions because an issue appears when I try to modulate...
hi guys,
I am using the nRF54L15 for software development. I have a requirement to define a space in the chip's internal flash for data storage. I referred to the soc-flash...
I have been experience that the if the device under a DFU process reports the error BUSY, because the external flash on the device is used for fileaccess the DFU process from...
Hi nordic support:
Our product uses the nRF9151 and prepare for GCF certification testing , which need to capturing LTE mode trace log .
We first intend to try running...
