Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
I am a beginner to Nordic devices and to Bluetooth technology in general. I have set up a Bluetooth connection using the nRF51 Development Kit and an nRF51-Dongle. The dongle...
Hello
In our production facility I need to read and write NFC NDEF messages to a NRF52832.
Is there any recommendation for a working and easy solution with an USB NFC...
Hi all,
I try to create a new project to update my firmware using twi(I2C) interface.
In my test case, first i download firmware to region2 via keil, then copy the firmware...
Hi Nordic developers,
For my internship I’m developing a BLE application on de NINA-B111 module which does have the nRF52832. I'm using SDK 15.0.0 and Softdevice 132 v6...
We're disabling pending FPU exceptions and clearing pending FPU IRQs before calling sd_app_evt_wait(), as per a few references:
https://infocenter.nordicsemi.com/index.jsp...
Dear NordicSemi engineer:
I want to connect to a peripheral device using a modified ble_app_uart_c.The information of the peripheral device is below:
How can I connect...
I need to allow BLE connections for a period of time after restart, then prevent connections (unless a button is pressed). Is this functionality as simple as re-configuring...
Hello,
I am currently developing software that scanning ble advertisement packets without pairing and advertise them like beacon. I used examples which are ble_app_hrs_c...
Hi!
I'm working on HID mouse example on SDK 13.0.0, SoftDevice S1332 v4.0.5. I'm supposed to use this as a low power media button control, using a nRF52 DK. I've done a...
Hello,
We wish to use nRF52832 IC in our design. We will design an equipment which can connect to another device via BLE and can send some measurement data. Our equipment...
Hey everyone,
I'm working with nRF52810 . I want to write into UCIRs before program execution starts.
I tried to configure NVMC(Non Volatile Memory Controller) and then...
I am using the nrf905 in a project. The datasheet suggests crystals of 4mhz, 8mhz, 12mhz, 16mhz and 20mhz are all acceptable. Does the choice of crystal oscillator frequency...
Hi there, I have an 70mm wide and 50mm high PCB with an free space of about 32x26mm on the right top corner. At the moment this area is free of any traces and polygons. The...
In previous questions I inquired about setting the MTU size beyond 27 and thank to the answers I, indeed, manage to compile and run my program with larger MTU size definitions...
Hi, I have an issue with the watchdog and sd_app_evt_wait() when running the softdevice. It seems impossible to not let the watchdog go off while having an idle ble connection...
