I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hi,
I'm using the SDK10 bootloader and DFU mechanism. I can update the firmware using Master Control Panel 3.10.14 on a PC, but the update fails using the iOS library or...
Hi,
I want to turn peripheral device from application mode to bootloader mode from a central device(not app), so I am trying to write value 0x01 to dfu service.
Following...
Hi,
I am trying to evaluate the NRF51822 with S110 softdevice stack. My IDE is the IAR Workbench 7.10.1 for ARM. I downloaded the most recent s110 version (s110_nrf51822_6...
In the product specification page 165, I see than the continuos mode is 2 to 16kbps. In the page 167 this mode is 2 to 16ksps.
Which unit is correct, kbps or ksps?
If...
Recently I have put some code of my application into RAM. When I do not enable read back protection mechanism everything works, however when I want to enable protecting my...
Hi all,
I have updated a custom automotive PCB and am now using the nRF51824 instead of the nRF52832 I had been using previously.
Unfortunately, I have been unable to...
I am very excited about the Bluetooth 5 LR PHY, but do you plan to release an update to the nRF5 SDK to support the newest soft device S140 v5.0.0-3.alpha?
Hello
I am new to work on nrf52,
Please can someone help me regarding how to use hardware and software pwm together. I have a need of using 13 leds , so i need 13 pwm...
Please can anyone help me on how to use(program) PWM hardware with individual loading mode? My goal is to control 12 LEDs individually with different duty cycles and playbacks...
I want measure the current of a device over a resistor. It is connected to 5V which is over VDD(3V) of nRF52 Chip.
5V--->10ohm--->Device
the differential voltage of this...
Hi,
I am using SDK v8.0.0 , Softdevice s110 and Example is ble_app_uart(peripheral).
i want to reduce a range of nRF51822 beacon(PCA20006) up to 2-3meter..
i try this...
Hi all,
Basically I am doing an exercise on the BLE system use case. Let's say I want to setup a BLE system where there are the long range BLE capabilities in Relays and...
What is a minimal length of preamble, such that nRF51 is able to safely receive a packet with? Can it be made (via some magic registers) to be as small as 4 bits? Then it...
