Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi, I'm developing a wearable fitness device. The device collects accelerometer-gyro data and sends it to the mobile application. Initial developments are good, I created...
I'm using the <TWI Scanner> example. I use an oscilloscope to measure the signal of SCL (see image)
According to the datasheet, I'm connecting a 4.7K resistor to connect...
I am using the two units talking with each other for the BLE uart.
One is running with the example ble_app_uart_c_central. The other is running with the ble_app_uart_peripheral...
Setup:
Node: 1 nrf52840dk acting as a node flashed with mqtt_client_publisher running on top of OpenThread using the nrfSDK for Thread and Zigbee.
Debugger access via...
How are the pins of the nRF52840 used in the Nina B301 mapped into the Arduino / mbed os system? Using the pin mapping files in the ARduino code often doesn't seem to work...
Background: we have a nRF52832 based design that's been used for the past 1-2 years across a couple 100 piece batches. Our latest batch of 500 boards shows an odd behavior...
Hello all,
I'm using a nrf52840 and it's working fine. However, when I supply the chip with 5v on VDDH the GPIO output voltage is 1.8v. When I supply the chip with 3.3v...
Hi,
We are trying to use an nRF21540 FEM with nRF5340 running the latest nRF Connect SDK. Please can you advise how we can generate the necessary TX_EN/RX_EN signals to...
Hi, devzone
I tested nrfutil6.1.0 dfu ble feature and pca10040 as host board to upgrade another board pca10040, successful!
when test nrf connect desktop v3.6.0 and...
Hi,
I want to use my MPU6050 sensor for my nrf5340pdk board using I2C.
But I face some problems with including the sensor driver.
In my prj.conf file, I do the follwoing...
Dear support,
I am developing a TDMA protocol on a custom board with the NRF52840 and SEGGER EMbedded Studio and the SDK 15.0.0. Everything went well until I wished to reduce...
Hello everyone,
I'm using a custom bt gatt service. Everything works fine untill i want to use a service that sends data through notification to the adapter side. I get...
Hello,
I have query about ANT burst mode, I want to confirm that which mode of ANT BURST uses automatic retries and which does not. Here is a document which states ANT BURST...
