Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
Hi, We were trying with a new n/w carrier in Canada ( Maxim ). nrf9160 is able to connect to the network, but it is not able to resolve our server URL ipv4 address. Below...
Hi,
I am testing RX mode.
And the module is sure to enable M1 (%XSYSTEMMODE: 1,0,0,0)
I use the following command, but return error.
AT%XRFTEST=1,1,2,19500,17,1,0...
Hello,
I´m writing my thesis and using the Online Power Profiler to get a estimation about current consumption in NB-IoT cases.
I would like to use the diagram from the...
Hi, I have developed zigbee stack.
I tested to connect the door lock example of Thread and Zigbee SDK 3.2.0 with ZC of SDK 4.2.0.
I checked connection with these.
So...
Hi,
We are going to use NRF52832 for a project, and planning to design our own PCB card and assemble the NRF52832 chips, purchased through Digikey or a similar distributor...
Hi everyone,
I have designed a project based on the Radio test example, in the Nordic SDK. After programming all my code on the NRF52833 DK (PCA10100), i decided to design...
Hello, I have 4 NRF51822 modules, 2 stlink programmers, and a BLE400 board, I was using the same module with the same stlink each time, but the led on the board stopped lighting...
Hi,
I am going to transmit and receive data with libuarte. I read the libuarte example, but I am not quite sure my understanding of the data transfer process is correct...
Hello
I am trying to configure the spis with the nrfx drivers. My code is as follows:
I enabled the nrfx SPIS driver and the nrfx SPIS3 instance via Segger Embedded...
Dear,
I want copy antenna design from PCA10040 for BLE. Could you please help to provide antenna's spec, such as gain, efficiency, Radiation Pattern?
Thank you.
We are trying to program the nRF5340 via SWD from a host MCU and would like to understand if there is a white paper/blog post similar to this one:
https://devzone.nordicsemi...
Hi, Currently, we work on a project that uses: nRF9160 Zyphre OS Segger Embedded Studio for Arm (Nordic Edition) V5.10d SDK v1.4
This is our situation.
We want to measure...
A few things to preface:
Hardware: nRF52840 Development Kit (PCA10056 - 2.0.1 - 2020.11)
Nordic SDK: nRF5_SDK_17.0.0_9d13099
Central example project I am using: nRF5_SDK_17...
Hi,
How do we get the GPS speed accuracy out of the module? We have used other GPS modules in the past which have output the speed accuracy which we use to qualify the data...
