Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi everyone,
I am designing my own PCB using Raytac's module MDBT50Q-1MV2 that carries on the nRF52840 SOC.
The system will operate in normal voltage mode (VDD = VDDH...
Dear All,
I am trying to compile a project from the command line and I want to enable all the warnings possible for the files that I have created. I am using the NCS v1...
hi support team,
i tested the example of \\nRF5_SDK_16\examples\peripheral\usbd_msc , and SD card interface , that with the APP_SDCARD_FREQ_INIT 268435456 (1 M) and APP_SDCARD_FREQ_DATA...
Hi DevZone,
I created my project on SES in order to download files from a web server. So I decided to include in my project the "download_client" library which contains...
Hello! I am working on updating from SDK 15.2.0 to the SDK 16.0.0 and have encountered some problems when trying to use DFU OTA to flash my unit with the application.
I...
I need to be able to measure the battery level of the NRF52 with the internal ADC.
I know it can be done, but I don't really know how to configure it
I am using MBED...
I have purchased an nRF51822 module. I am using the Arduino IDE and the ST link to program the module. I have used the library BLEPeripheral by Sandeep Mistry (see below)...
I deleted a node in the mesh app without unprovisioning the node. I then reprogrammed the dongle hoping that everything will be reset. It seems the dongle is still provisioned...
I am following the example given in the SDK v16 with nRF52832/ nRF52840. For the given example UART is working fine. But whenever I am changing the default pin configuration...
Hello,
We are working on the NRF52840 with the SDK15.3 and the softdevice 6.1.1, we are trying to connect to different mobile centrals via ble. We are facing problems...
Hello,
We are trying to develop a gateway (central) to interface with off the shelf BLE devices. One of the functions of the device is to send logged data to the client...
Hi - I am trying to create a CLI project with FreeRTOS , the project will be used as an aggregator .
I can not figure out why I can't enable CLI , code hangs. would appriciate...
Hello, I have to use 2x VL53L0X in a development based on nrf52832, but I cannot find the adequate library for this share. Can I use the development library on nrf51 from...
