We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello all,
I tested adc example code. And i want to change this code with our requirement. But in example code, i am getting alternate values on fixed voltage.
How can...
I continue to successfully upload the Blinkey app via DFU. However, when I attempt to upload my development app it does not start. From what I read it has successfully loaded...
Hi
I am test the DFU function in nRF52840. I want to add a timer to the bootloader to generate a one-second sleep action. But when even I have not started to use the timer...
After enabling both the Macro MESH_FEATURE_RELAY_ENABLED and MESH_FEATURE_GATT_PROXY_ENABLED as mentioned in this link ....
Does the proxy and relay feature work for light_switch...
Hello Support
I have a question about the function " uint16_t otCoapMessageGetMessageId(const otMessage *aMessage); ". I need to know the message ID for my application....
Hi,
I am facing a problem while setting up pyaci on Ubuntu 20.04.
On launching the command:
In [4]: p = Provisioner(device, db)
I am getting:
In [5]: 2020-08-04...
Hello guys,
In our current project, we need to have the ability to copy .bmp images from our PC directly to W25N01GVZEIG TR QSPI flash memory of NAND type. To the best...
Hello, i am new to the whole NRF programming. I created my custom board with a NRF52811 SoC, without external LF crystal. I have been trying to get the device to advertise...
Hi all,
I am working on eddystone scanner and I follow this post to start with. However, I have some problems:
1. The device isn't scanning without any modification of...
Hello Everyone,
I am a beginner and working on nRF52832 DK using SDK v13 and using keil mdk armv5.as a compiler. I build it successfully, but when I loaded the hex file...
I am trying to update the firmware on the Thingy:91 following the instructions here: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nc_programmer%2FUG%2Fnrf_connect_programmer...
Hi
I am using nordic thingy 91 and i want to program my application on nRF9160 and nRF52840 respectively and i am following the getting start guide.
first i was able to...
SDK 17.0.0/ Windows/nRF52840 DK/ SEGGER
Hi, I want to learn how to achieve the outcome of allowing the peripheral to advertise in the long-range and the Central DK to pick...
Hello,
I have an application in which I need to get RSSI before, during and after any BLE connection has been made. The RSSI measurements are being used to quantify the...
