I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
I am using nRF 52 DK connected to Arietta with ARM Linux (4.2.6) 32 bit.
when I was trying to install "vcpkg" using "./bootstrap-vcpkg.sh", I am getting some errors as shown...
I have a phone app which talks to my peripheral device running the nrf52832 and so I will eventually add another peripheral device which ideally can communicate directly to...
Hello everyone!
I'm working on a project where there are 2 microcontrollers: the Nordic nrf52832 and a 3rd-party uC (can't disclose it). A protocol to transfer the firmware...
I feel confused about bearer. what's the difference between mesh-bases bearer and PB-ADV bearer or PB-GATT? there is little knowledge about mesh-bases bearer within mesh profile...
Good afternoon,
At the place I'm working there's 2 main projects using the nordic SDK, while one runs on the 12.3 version, the other is very outdated and still runs on...
Hi,
I'm having a problem at the moment with code based on Espruino on nrf52.
I connect as follows:
ble_gap_scan_params_t m_scan_param;
memset(&m_scan_param, 0,...
I've seen a few post that have similar issues but none that solve my problem.
I have two uarts (uarte0 and uarte1).
I disable them before going to sleep.
I wake with...
Hello,
I cannot successfully flash an nRF9160-Dk to a usable AT modem state using a brand new install of nRFConnect on Windows10, following this Blog post guidance - https...
I am working on 802.15.4 using nrf52840 and sdk 15.2. I want the receiver node to scan the network for beacons transmitted by the transmitter node for 100ms, go to sleep for...
So its seems nrf9160 docs recommend having VDD_GPIO only at 1.8v ... that running at 3.0v (or 3.3v) will compromise LTE performace.
I have 3.3v rail and 3.3v SPI device...
Hi Folks,
I'm trying to use the Power Profiler Kit. Unfortunately I keep getting 'Failed to start the PPK'. I've updated the drivers (and can program the nrf52832 DK with...
In the nRF52840 Product Specification v1.1 ( HTML ) , description of the QDEC peripheral, Table 77 on page 275 ( direct content link) , it appears to indicate that the LED...
Hi,
We have an freertos based app (SDK14.2).
Recently we have added a WDT support in the following manner:
The init code initializes the WDT reload value to T+3...
