I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi,
I tried to program the Thingy52 with the node and bridge to set a Mesh and I got the message in red you can see at the attached.
Please advise.
Thanks
Hi,
After reading the nRF24L01 documentation, I have some questions regarding page 66 of the documentation ( https://infocenter.nordicsemi.com/pdf/nRF24L01P_PS_v1.0.pdf...
Hello,
Has anybody achieved to perform Mesh DFU over serial on a Raspberry Pi using nrfutil?
I can successfully perform it on Windows 7/10 (intel) so far with no problems...
Hi All,
I am running a modified example of the 'ble_app_multilink_central_pca10056_s140' project.... I am running this on a PCA10059 dongle. The project connects fine to...
I am getting following error while building the project.
undefined reference to `nrf_drv_timer_pause'
undefined reference to `nrf_drv_timer_clear'
I believe these...
I have uploaded the AT CLIENT firmware and I have connected my nRF9160 dk to my apn, but I don't find any type of AT commend to set a socket and open a port to send and receive...
Hi,
If fires multiple generic_onoff_client set LED = True command from PyACI libraries with Ack = True to multiple nodes, the generic_onoff_client will provide a "generic_on_off_status_handler...
Hi sir,
I want to know if nRF9160 is programmable or not, like other wireless microcontrollers i.e nRF51/52 and ESP32 etc.
If it is programmable, where can we find the...
Hi,
Can we do DFU-OTA on nRF52810 controller ? why i am asking this is , when i saw a video about DFU-OTA they saying that only the controller having at least 32 kB RAM...
Hi,
I would like to know if the access address of the advertising physical channel is affected by this Errata. As far as I understand it is not affected by Errata 107. ...
Hi,
I have developed custom nrf52832 board without external low frequency clock source.
So with that configuration I got problem when try to connect it through nRF MESH...
Hi.
I use Thingy52 B'd.
I want integrate Mesh into Thingy52 Full service demo.
I tested and merge nrf5SDKforMeshv310src/examples/sdk_coexist/ble_app_uart_coexist and...
nRf connect - When updated form v2.6.0 to v2.7.0 the terminal window of LTE Link monitor stops working. No debug info - No AT commands. The same time the Programmer App is...
