Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
checking most of the reliable coin cell CR2032 such AS Panasonic declare on very very low current transfer far lower then 5 mA
if i set my Ble in 5mA IO OUT ....when my...
NAND or NOR flash memory to use with nrf25832? my application is to store the data from mpu-9255 to flash memory. my data rate is about 3 mega byte per hour and i have such...
Hi,
I am using Linux ubuntu 14.04 with kernel version 4.15.0-041500-generic for 6lowpan over BLE and MQTT broker wit IPv6 address as inet6 address in below image
In...
If I use DeveloperStudio_1_1_3139_0 to generate a profiles and services for the latest SDK 15.x, will it correctly work?
I recall back with SDK 11/13.xx it was not compatible...
I need to sample ADC channel at the fastest deterministic rate.
If i use burst mode with 3us acquisition time, do i get a sample exactly every 5us?
does t(conv) is always...
About example BLE_uart,
My device must always remain in advertising, I'm using a 1280 ms between two advertisng event.
I have to minimize the consumption during advertining...
I have a few questions about the NRF6707 Power Profiler kit and I would like to ask you: 1. The NRF6707 Power Profiler kit and nrf52 DK are linked through the ARDUIND D0 pins...
I am updating the application software that was created based on ble_app_multilink_central in SDK 9.0 to 12.3. When replacing device manager with peer manager, I received...
I'm just getting started with the Nordic chips so I will apologise now if I have failed to find my own answer amongst all the devzone content.
I want to use the NUS service...
Dear all,
I have a problem with secure connection between Android (nRF Connect) and my custom board with nRF52832. I'm usind SDK 14.2 and SD_132 v.5.0. I'm using secure...
Hi All,
Anyone know the aggregator example can run on the nrf52 PCA10040 DK?
https://github.com/NordicPlayground/nrf52-ble-multi-link-multi-role I fail to compile the...
I've got a bit of an issue with turning off specific debug statements. If I try and adjust the log level, I get a run time failure. If I try and comment out the specific debug...
I have changed the RAM (rwx) : ORIGIN = 0x20001fe8, LENGTH = 0x2018 in ble_app_buttonless_gcc_nrf51.ld. Build, it appears to me /usr/local/gcc-arm-none-eabi-4_9-2015q3/bin...
Hi to all,
i have an example that it implemented a device with some charactristics, when i use sniffer to sniff these packets i can not see the packets data because the...
I am experimenting with the mesh light-switch example. I want to control two LEDs on a single node using the SimpleOnOff model. I know I should add a separate element and...
