I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hi guys!
I wanted to ask that can we use an external flash(connected via SPI/I2C interface to the mcu) instead of internal flash for storing downloaded image(s)?...
Background: We use NRF52 chip along with SDK 12.1.0. Since we have a few components of firmware (i.e. secure DFU settings, secure DFU , application, Softdevice) that go into...
The aim is to use the nRF51822 chip beside the application processor and to run the soft device S130 in it but as I saw, the newest SDK v12 supports only S132 Connectivity...
I am trying to update my S132v2.0.1 devices over the air to S132v3.0.0 and am getting no bootup, even after swapping dfu_dual_bank.c from the answer below.
devzone.nordicsemi...
I am studying this tutorial: nRF52 Online Power Profiler . I know this tutorial basically related to the ble_app_pwr_profiling example in the SDK: Power Profiling Application...
Hi, Nordic
I know pipe0 and pipe1 are be enabled on nRF24LU1 nRFgo SDK example for default PRX.
Now I only to enable pipe0, disable pipe1.
First, I use this...
Hi, Nordic engineer
nRF52832 as ESB PTX, nRF24LU1 as ESB PRX
same channel, crc, and match address and pipes, but from nRF52832 uart log, ESB TX fail event always show...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
Hello everyone~
Although one TWIM interface of the nRF52832 can "interconnect up to 127 individually addressable devices", I still think that use different interface will...
Hello everybody.
I'm trying to modify the original firmware that comes with the nRF51822 to make it sweep all of the permitted levels of transmission power.
I was able...
Hello,
I want to read the temperature value continuously on mobile scanner app. I implemented the program as stated in BLE Characteristics beginner tutorial and I am using...
Hey guys,
I’m trying to come up with a way to know if an advertisement was received via BLE_GAP_EVT_SCAN_REQ_REPORT, but then not actually send the SCAN response. It’s...
Iam using softdivice 110 and sdk 10.0.0, iam using spi driver for interfacing with spi slave device(flash memory device). I need to send command and then receive the data...
Hi,
I am trying to implement an ECG measurement device. nRF52832 collects the sensor value through SPI and send it to smartphone using ble_app_uart code. I need to send...
