Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I'm using PCA10056 (nRF52840 DK) for a project. First-time user, so little experience with this board.
I need 1.8v level SPI signals from the PCA10056 since I need to talk...
Hi
what is the current consumption for LPUART (when there is no event - let's say it is sleeping) on nRF9160 and on nRF52?
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hello,
I have a problem regarding the connection to the cellular network of the nRF9160DK.
When I boot up the device and I have uploaded a code to connect to the network...
Hi,
We have a custom software for our custom board. And would like to investigate a little in the AT commands going to the modem and the responses
is there a config...
I am using Connect SDK v1.7.1 and Ozone v3.26b. When I click "Debug with Ozone" in VS Code, I receive the following warning in the Ozone console:
I am able to correct...
Hello,
While developing the device, I found that the SAADC module on the NRF52833 incorrectly measures the voltage on the NRF_SAADC_INPUT_VDD channel if you set the REGOUT0...
Hi,
We have a device in production based on nrf52840 which uses UARTE to TX/RX data to/from a washing machine and in paralel communicates with a Phone App via BLE.
SD...
Hi,
I am using nRF5340 Audio DK. I have 3 kits currently and I have programmed one as a headset and the other two as gateways.
I would like to use the whitelist so that...
I think it'd be nice if there was a connect button like this.
but my device appear one button.
I think the multi-link function should be possible to solve this problem...
Is there a working example with using gpio_dt_spec for accessing gpios?
I used the code provided from https://docs.zephyrproject.org/latest/reference/peripherals/gpio.html#c...
Hello, by usingnrf52832 DK and testing some examples i found out that the example peripheral UART was not going like I wanted to do. He is going to sleep mode after 3 minutes...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v1.0.1%2Fmd_doc_getting_started_how_to_models.html
Linkte verilen yönergeleri takip ederek...
Hi all, I discovered that if I get BLE_GAP_SEC_STATUS_AUTH_REQ while pairing, the device is basically useless until a new reset. I would be extremely grateful for some help...
