Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
I know Nordic is releasing the nrf9160 on the 12/12/2018, and from what little documentation I can find it doesn't seem to have BT or NFC hardware integrated. Are there any...
Hello, I have installed nRF Connect and the Programmer following https://infocenter.nordicsemi.com/pdf/nRF9160_DK_Getting_Started_Guide.pdf At step 3.2.2 i see "No devices...
Where can I find a drawing of the footprint for the nRF52840 WLSCP? Normally it would be near the end of the datasheet, after the mechanical drawing of the package. The datasheet...
I have an application running a serial communication through a RS485 interface. I have two sensors attached through I2C/TWi.
I have a app_timer that quwry the sensors once...
I have built on the CoAP example a POST request to the server. This works now without any problems.
I do send the received signal power within my POST. To get the power...
Hi,
I purchased a NRF9160 DK and am having problems on the first time I am trying to compile the SERIAL_LTE_MODEM application . I followed the steps according to the documentation...
Hello,
when I open any example Project from https://www.nordicsemi.com/Products/Development-software/nRF5-SDK with Keil MDK v5, I directly get the Error Message "Cannot...
Hello,
I'm a beginner of nrf5340, when I tried hci_pwr_ctrl(ncs v1.5.1) , I met some problems.I adjusted the tx power and changed prj.conf :
Then I added hci_rpmsg...
After updating nRF Connect and the Programmer app, DKs aren't being recognized when clicking on Select Device.
Tried both with nRF9160 and nRF5340 DKs and neither was detected...
I'm working with the PCA10040, the SDK V11.0.0. and the winbond memory flash W25Q80BV.
For the SPI connection I'm using the the SPI2 because TWI0 and TWI1 are being used...
Hello
First of all, I`ve been spending way to many hours trying to figure this out, so I decided to open this ticket. I am new to microcontrollers in general and the Nordic...
Hello:
I'm new on nrF52832 development. I did some tests using nRF51 and so far so good. However I received a few samples of E104-BT5032 from eByte http://ebyte.com/product...
Hi,
I have 2 SES projects that both require softdevice plus application.
One of the projects combines application and softdevice into the .hex file that is generated...
HI
I am Programming in Keil IDE and I am using ST link v2 like debugger, but in Keil shows this problem "internal command error"
what is the problem? I was thinking...
