I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
I am using SDK17, nRF52840 based custom board and SoftDevice 7.2.0 with SES.
I want to use SDK's secure bootloader (pca10056_s140_ble) with my own keys.
To enter to...
Hi,
I have used a Custom board using nrf52832. It follows some procedures. After that, it needs to get into sleep mode for a time which was sent from the app
I use the SEGGER Embedded Studio for ARM IDE to build a clean build directory. From the IDE I can build the project and it completes successfully.
So I then take the same...
We have a product that uses a module containing NR52832 and also both 32kHz and 32MHz crystals. This has been operating correctly and is in full scale production.
On our...
Hi,
I'm having some difficulty debugging an issue with the mqtt library on the nrf9160dk.
I have written my own Cmqtt library class that wraps the Zephyr mqtt library...
Dear ,
On Windows 10 Bluetooth add a device,
Why SDK_17_0_2 Example does Bluetooth be disconnect immediately after pairing
(Use about \nRF5_SDK_17_0_2\examples\ble_peripheral...
When I open the Light Bulb project in Segger Embedded Studio I see a bewildering list of project items. I pick the first project, 'zephyr/merged.hex' and right click to set...
SDK: 4.1.0
CHIP: 52840
Hi, I have developed sleepy zed. It lost the connection with the network after joining in 1~3 days.
It assumes that the zed couldn't get the...
Hi, guys.
I'm using nRF52 DK (PCA10040). After I used Zadig (Driver setup for J-link), I cannot build and run my previous code to the nRF52 DK anymore (see the first 3 images...
Hi
I am using nrf52840 boards and by using the coexist program I am able to send and receive messages through mesh while using the ble services.
I followed the instruction...
I use NRF52DK as central device I also use a SDK that is ble_app_uart_c code for my project. and i would like to take my peripheral devices whice are phone or PC their RSSI...
Hello - we're using "nRF Connect" from the Apple App Store for the development of our project.
First, thank you for making this tool available and free for everyone to use...
I am using nrf52840 via NRF Connect and Zephyr configured to use the Nordic SoftDevice BLE controller.
My use case is for a central to sample a rapidly changing real-time...
As a beginner,I’m sorry for asking such a stupid question,but it has annoyed me for a long time.
I built and downloaded the program to my DK,and I used PuTTY to connect...
Hello,
I've designed a pcb using the 52840 chip which is essentially identical to the dongle design. My intent was to use the firmware that comes pre-installed with the...
