Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi everyone,
I am making a project to dim a led strip following PWM driver example, everything works pretty well but i only have one problem that I need to set a state for...
Hi,
I'm trying to debug my application using monitor mode debugging and after setting a breakpoint while the code is running I usually have an assertion that fails in the...
Hi,
I have downloaded the nrf5 Sdk 17.02 and nrf mesh 5.0.
Kit:nrf52832
Ide:segger ide
1. Can you please tell me how the data gets transferred and stored in ble stack...
Hi!We used a 52832 to make a bracelet. Now some apps on Huawei phones can't be remotely upgraded by the ring. We have verified that Nordic's official Android DFU library throws...
Dear Sir,
I'm testing the Rx sensitivity of EVB (nrf52840-DK).
I use PER 30% be the thresholde and get Rx sensitivity; -92 dBm/ 1M , -88dBm/2M.
It's different with datasheet...
Hi Nordic,
I have upgraded my NCS folder to version to v1.4.2 and couldnt able to open SLM application(v1.4.2\nrf\applications\serial_lte_modem).
I am receiving below...
Hi,
probably very basic question. I found some nrf code in nordic sdk. I don't remember the version of SDK. I compiled and deployed it on nrf52840 devkit and also on dongle...
The issue:
1) Program x2 NRF52840 dev boards
2) comment board A to windows, windows reports COM n
3) unplug board A and connect board B
4) windows reports the same...
Hello Everyone,
We are using nRF52840 IC for our products which has 1 MB of flash.
Thread Secure DFU Example provided with Nordic SDK supports only Dual Bank DFU. This...
hi,
we have an product using 51422 for many years, now customer ask support dual bel connection, please help confirm if it is possible? which sdk version and if there...
The chip we use is nrf52832 and the SDK is nrf5_ SDK_ 15.3.0_ 59ac345, the booeloader uses the example project nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040_ble_debug...
Hello,
I am developing one Zigbee based product for that I am using nRF52840 and light_bulb examples and modified as per my requirement.
Till now everything successfully...
I've just found through some trial and error that SoftDevice (s130 at least) on the nRF51 DK handles a sequence of notifications in the following manner:
call sd_ble_gatts_hvx...
