We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello,
I try to add the BLE-Template code into my existing program code, but I get the following linkage error. I have defined the following flash_placement.xml for my Segger...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
Hi,
Add BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event handle at ble_lbs service in example of ble_app_blinky. but when client read the characteristics 1524 or 1525, no BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST...
Environment: Windows 10 nRF Connect SDK 1.4.0 I followed all of the steps described in nRF connect SDK documentation and tried to build "Blinky" sample from zephyr as shown...
use s132 on NRF52832
when i used sd_ble_gap_connnect () to connected peripheral device,it return NRF_ERROR_INVALID_ADDR
the addr copyed in scan_evt_handler() by NRF_BLE_SCAN_EVT_FILTER_MATCH...
Hi ,
I have made basic binary sensor based on light bulb project,
wanted to add default BIND-TO-Gateway ( Short address 0x000). Gateway is CLI_AGENT .
I am try to add...
select at_client folder
west build -b nrf9160dk_nrf9160ns -p
shows this warning
```
warning: The choice symbol LTE_NETWORK_MODE_NBIOT (defined at /Users/paul_tanner...
Hello, we are using a usb dongle where we have a NRF52840 and RFX2401 PA+LNA frontend. The latter can be controlled with TX_EN and RX_EN pins. Please see attached schematic...
Hi there,
I'm using ARMGCC in combination with Make, nRF5 SDK, nRF SDK for Mesh, FreeRTOS and C++. Everything except one single thing is working. I've just implemented FDS...
I have installed the sdk v 1.4.0 via the toolchain manager (nrf connect 3.6.0). I am using windows 10.
Here are my problems :
First I dont have the launch ide button after...
Hello Team,
We have already done the PoC for the Openthread network. I have created a border router using nRF52840 as an NCP and multiple nRF52840 end devices.
Now my...
If I have a firmware project working reliably on the nRF52810, is it possible to build a single firmware image that will run on both the nRF52805 and the nRF52810? I'm not...
Hi,
I was trying to program my board using SEGGER, but it doesn't seem to be working (log provided in the picture below)
/resized-image/__size/320x240/__key/communityserver...
