Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Dear all,
I am very new to BLE developments and Nordic product, I have purchased the nRF52840 dongle to have a feeling on the product ( I understand I should get the nRF52840...
I have below queries Regarding Secure Boot and DFU:
1) Is the secure boot functionality available in nRF52840, if available please provide the procedure for doing it?
...
Hello, guys!
We are excited to start a new product prototyping by using Thingy:91 board. Consequently, I would have a few questions related to Thingy:91 configuration...
Based on sdk15.3, adding the 0x2902 descriptor to the rx characteristic of the ble_nus service resulted in an NRF_ERROR_FORBIDDEN error.
My code is as follows:
ble_add_descr_params_t...
Hi,
I'm using S112 v6.1.1 with SDK 15.3.0 on nRF52810.( I don't use bootloader )
I tried to search examples for using fstorage api on it.
But I couldn't get anything...
Hi,
Recently I came across this example which gives mesh & uart in single application. now i'm trying to add GATT proxy to it so that i can do provisioning via nrf mesh...
Hi,
I have read the dfu protocal and found that there are three types of dfu transfer which are identified by a firmware ID. Now I want to add a new part to update the user...
Dear,
I am using THINGY91 for proving my concept, I put THINGY91 in the freezer - to adapt to the temperature.
I am using NB_iot of telia (norway)
My problem is: sometimes...
Hi,
I am using the NRF52832 with softdevice 6.1.1
I am using the minimal ble_app_uart ecample, just changes the RX_PIN_NUMBER to 11 an TX_PIN_NUMBER to 12 to mach my board...
Hello ,
I want to read the values from tera term , and PCA10040 have to read that value on polling basis .
Then advertise that values / data as manufacturing data. i am...
Hi
it looks like my MQTT-SN is not working.
I am trying to run MQTTSN Example in nRF52840 devices. https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hi,
I have 3 Devices that constantly broadcast their position to each other so the other can adjust the position each other. they act like master and slave but ther are...
I'm trying to get the most performance per mA out of my nRF52, for test purposes I've used the nrfx libraries to communicate to the peripherals but I want to make my own....
