I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
Hi, I've got an application where I need to send a message and then receive a response on a half duplex serial link.
I feel like this is a pretty common use case but the...
Has anyone added cpputest ( https://cpputest.github.io/ ) to Segger Embedded Studio and can share the setup? Can build with some minor changes (had to disable CPPUTEST_USE_STD_CPP_LIB...
Hi,
I'm trying to integrate the light switch server example in nRF5 SDK for Mesh v4 with ble app beacon from the nRF5 SDK v16. I added the advertising_init and the advertising_start...
hello again,
i spent the last three days on the theme dfu, bl, app, sd. Now there are some questions I can't answer me with reading.
Question 1) Does a new app works ...
Hello!
In our design we need BLE 5 solution with maximum allowable by reulation +20 dBm TX power. It is not a problem to use a separate PA for achieving that power, however...
Unable to obtain repeatable scan response data.
I can obtain advertising data and scan response data from 3rd party devices. I can obtain advertising data from my server...
When initializing models from the models_init_cb it's useful to check the current configuration using the mesh config API. However, the returned values are always the default...
We are testing GPS capabilities for our hardware, using mfw 1.1.0 in the field. We have the following test conditions
The unit is ackquiring position every 5 min
the...
Hello,
We are trying to run the ble_ant_app_hrm example on nRF52840DK using nRF5_SDK_16.0.0_98a08e2 SDK and ANT_s340_nrf52840_6.1.1 softdevices (both latest as of today...
Hi,
I was looking for information about the MLME-ASSOCIATE primitives in the https://infocenter.nordicsemi.com/ . The section with the "MAC MLME Association API" title...
Hello. After I updated the firmware on Thingy 91, it no longer registers on the network via LTE - the LTE indicator in LTE monitor blinks between yellow and red, and I get...
Hello Nordic team,
I was wondering how to determine the QDID of our product. The relevant QDIDs are 101625 and 97989. I believe the latter should suffice but I am not sure...
Sir After Flash the code to board i am getting some info message in teraterm
below i have attached the image of the teraterm
Refereed link: https://infocenter.nordicsemi...
Hello Nordic team,
I'm using an nRF52840 with SoftDevice S140 version 6.1.1 which size is 0x25000 (without MBR).
My bootloader contains the bootloader code written at...
Hi to all,
Happy New Year 2020 !
I have developped an application with the nRF52832 ( nRF52DK ) and I use the SAADC for battery level every 2 hours ( no need of precision...
