Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi all,
I am working with SDK Thread V3.1.
I run simple_coap_server and simple_coap_client.It run normal.
Now, I want to add DTLS for this example for secure data. ...
As far as I understood, the flash protection can be realized by writing the 0x00 to the lowest 8 bits of UICR APPPROTECT register either putting it code image or via the nrfjprog...
Hello,
I use NRF52810 with SDK 14.2.0 and softdevice 112. I need to use 7 input pins, but if I config more than 3 pins, all signals disappear.
GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS...
Hello all,
SDK:S332 V4.0.5(related to BLE V4.2).
Platform:NRF52832.
For improving BLE data throughout, i tried to set some configurations by other guidance.
Following...
Hi Tech Team,
I am using nRF52832 chip and the recent soft device(SD). I want to implement my own file storage and thus using sd_flash_write () and sd_flash_page_erase functionalities...
Hello Nordic experts,
I am using nRF52840 and SDK 15.3.0. I have added an OUT ENDPOINT to the usbd_hid_generic example by following the suggestions in https://devzone...
Hi,
I'm new to programming and I can't seem to solve this error of "No such file or directory" even when I already put the file in the location of the directory.
How...
I am writing a 1-wire driver (there doesn't appear to be one in the SDK), and am looking at dynamically switching the GPIO between read/write. There appears to be two functions...
I am running the light_switch example and it works fine works fine , I am using the nrf_application to configure the nodes.
I am using latest mesh sdk and 15.3 nrf sdk....
Hi guys
I had to integrate a CLI module into a project I'm working on, that is running FreeRTOS
after quite a lot of work, I managed to get this working, but seeing...
HI,
I am using nrf52832 dk. I have a sensor that gives a negative voltage. I want to measure the value using saadc.
and can I use differential mode saadc for negative...
Hello All,
I am working on the N51822 custom board.
Using segger IDE, SDK 12.3
Previously i have worked on the sdk 14.3 on the n52810 board. It is working properly...
Hello
I am using pin 1.15 of nrf52840 dongle with transistor with enable pin of another chip. The other chip is a wifi chip which I only want to switch on whenever I have...
Hi All
I am using nRF9160 DK version 0.8.5, and I have gone through this link, downloaded and Installed all the steps, given there. All seems to be running good.
But some...
