I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
I have a few questions regarding AoA mode.
My goal is to append the CTE frame too a standard advertisement frame. I would like to use one of the following examples as the...
Hardware: nRF52840, running on dev kit PCA10056
Software: SDK 15.0.0, no soft device
I'm trying to get the POF comparator working, and after struggling in our product...
I just updated my project from SDK 15.3 to 16.0. I am using the nRF52840.
I am not receiving the APP_BUTTON_RELEASE event when waking up from a button press. It used to...
I am trying to the asset tracking application on nRF9160DK and following the steps mentioned in https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started...
Hi there,
I have tried to build mqtt_simple but ı got an error says:
#error bsdlib must be run as non-secure firmware. Are you building for the correct board ?
I am...
Dear Support Engineers
I am in the process of designing the automated testing platform for a 52832 based device and would like to test to make sure the components/devices...
Hi, I am trying to test the examples provided in nRF5_SDK_16.0.0 on nRF52840 (PCA20035) thingy91 device. But unfortunately, i didn't see the support files for pca20035. For...
I am using nvs_init(), nvs_read(), nvs_write() calls to store and retrieve user data. Everytime I flash a new image I use the following commands:
# nrfjprog -e -f nRF91...
Hi!
I was wondering about the Receiver Category of the nRF52840 according to EN 300 328. The device should be classified as a category 1, 2 or 3 receiver, based on the...
Hello,
I recently bought a nRF9160 DK version 0.9.0, I did a few software experimentations on it and now I would like to restore the certificates properly.
I followed...
Hello,
I am new to cloud development and was wondering if there is any more documentation or tutorials on how to use the Device APIs for nRF Cloud in addition to the guides...
Dear Team,
why is that the command " AT+CCLK" returns time with 2hours of difference? How should one compensate?
AT+CCLK? +CCLK: "19/07/19,19:57:30+08" OK AT+CCLK? ...
Using a multimeter and a Thingy:91 I've measured the current to
The nrf9160 ( infocenter.nordicsemi.com/index.jsp
The nrf52840
The total (measured between battery...
Hi,
The following article describes how to perform serial programming of nRF9160 on Thingy91: https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started...
I connected to nrfcloud using a SIM card from iBasis and the asset tracker example.
Is it possible to connect to nrfcloud using a SIM card from another vendor? (in my case...
