I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
When building a project I get a number of undefined symbols:
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol __start_fs_data (referred from nrf_fstorage.o)....
Hi,
I am planning to design a custom board using nrf52840 Soc which receive analog signal from sensor and send ADC outputs through UART to smartphones using Bluetooth communication...
Hi, Everyone
I use sdk15.2 & nrf52832
I am doing a test to read the slave address in TWI
There is one slave device on the board and the slave address is 0x68
I used three...
I am working with SPIS example ( sdk version 15.3). SPI master send data regulaly. For example, it sent 5ms cs low, but there are only two bytes transferred, the first byte...
Hi,
I'm working on a project that is using the the freeRTOS and I want to use the NFC pins P0.9 P0.10 to drive SOFTWARE SERIAL UART with a timer like TIMER1, when I try...
iPhone 8 Plus with nRF connect App[iOS], does not shows BLE 5 beacon in scanning, it only scanning BLE 4 beacons, In Spec of phone it shows it support BLE 5
nRF connect...
Hello,
I follow the nRF Connect SDK on a Windows 10 x64 computer and it's a crap. I get a lot of errors like this one. It's so crappy that I doubt that I will continue with...
Hello,
I am not able to send a command from the BLE (52810) to a DSP over UART which are on my custom board. I have modified a program that uses UART for logging purpose...
The s132_nrf52_7.0.1 documentation says: Call stack: The SoftDevice uses a call stack combined with the application. The worst-case stack usage for the SoftDevic e is 1.5...
I am doing a program based on Current Time Application example. But I have a few questions, so I hope you can help me. First, I am using Battery service together. By the way...
Hi,
In our current project we use nordic NRF52832 ble to send some data(~200 Byte / packet) to host, we expect each transmission to be done within 10ms, but results from...
Hello. nRF52 A custom board is being developed. I want to use Crypto Chip Pulse to encrypt. Pulse_Out of Crypto Chip is connected to P028/AIN4. In order to measure Pulse,...
I'm using \nRF5_SDK_15.3.0_xxxxx\examples\peripheral\usbd_ble_uart example to use two communication links. Missing echo on the USB virtual COM is a small frustration. I've...
Hi NordicSemi
I have a project where we receive data via the UARTE. To avoid missing data caused by higher prioritized tasks we want to use the DMA facilities.
nrf52832...
