Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
I tried to use fs_erase and fs_store functions but they both return the value FS_ERR_INVALID_CFG which means "Invalid fstorage configuration". I'm working on nrf51822...
Hi,
I'm using SDK 14. I started from ble_uart application, and to use ADC as well I ported ble_app_uart__saadc_timer_driven__scan_mode (SDK 13) to SDK 14 (made changes in...
Hi,
I am implementing the whitelisting feature so that the NRF52 only pairs with one phone at a time. We require the NRF52 to advertise for 10 mins but I could only set...
IN looking at CONN_SUP_TIMEOUT below:
It says the units are 10 ms. if you take 4000 * 10 ms, you end up with 40000 ms which = 40 seconds - not 4 seconds.
Also for...
Hi,
As title, I'm the new for this.
I have one 52840 board and several 52832 boards, and one of them(sink) collect some data from other boards by using proprietary radio...
Hello,
We use nRF52832 with SDK-11 as peripheral in our project. We want to utilize white-list feature to limit the connection establishment. I have studied H ID Mouse example...
Hello, I'm trying to view the STATUS register of the timer (1 for example) but it is not display on the segger registers view ... Is it a well known problem ? Cheers, Sylvain...
I am developing application on nRF52832 with SDK14. I came across mem_section_dummy_rom and mem_section_dummy_ram sections in the linker script in the example codes. I couldn...
Hi
I have been using nRF52 in my project. I am not using provided uart drivers for one uart -> UARTE1. I am using DMA access and I have no problem to send and record messages...
Hello,
Can the nRFgo tool be used to compile/construct Gatt profile & service tables for nRF8240 devices.
If not is there a tool for construction the services (e.g. like...
Dear Sir,
Please tell me how to configure the NFC pine P0.09 & P0.10 as GPIOs. I followed all the procedure given in the development kli manual & on the nordic blogs also...
Dear Sir,
I am using nrf52832 & sdk 14. When I dump your twi sensor code(SDK14\nRF5_SDK_14.2.0_17b948a\examples\peripheral\twi_scanner\pca10040\blank\arm5_no_packs) in the...
Hi ,
Need a bit of help here.
I am trying to use TWI and SPI in a single code for communicating with two different slave devices, the LTC2941 coulomb counter and the EM4325...
I've adapted the SPI example to read a value from an Analog Devices ADXL350 accelerometer as follows:
But when connected to the accelerometer this hangs waiting for the...
