I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
I am making some NRF51822-based temperature sensor nodes, powered by CR2032 coin cells, and I would like to minimise power usage in order to maximise battery life. I am using...
Hi,
I am doing a BLE based project using NRF51822. I am asked to build a 2 layer board.
According to the reference schematic BALF-NRF01D3 has been used with WLCSP package...
Hi,
I'm close to finishing the implementation of a system with a recording device with nrf51822, working with 6 sensors with nrf24L01.
The recorder is in receiving mode...
I'm looking for an approach to RF coexistence between an nRF51822 bluetooth SOC and a WiFi module such as the WL1801. Does anyone have any experience or recommendations for...
Hi guys,
I tried to flash the pca10001\blinky_example onto a nRF51822 with nRFgo Studio.
Flashing the s110 worked fine. But when I try to flash the hex from the example...
Hello All,
I'm thinking a small plastic case for a portable device.
It is possible to place pcb board (with pcb antenna) above the battery (Li-Po) or can interfere with...
I want to log basic intermittent events and push them to a previously associated mobile device when one is nearby. The mobile device can then forward the events up to a server...
I'd like to know what is the minimum and maximum frequency I can generate on a GPIO with a 50% duty cycle (+/-10% at the worst case). Which resources should I use for that...
In my case active CE signal defines byte boundaries - for each byte individually.
From what I see, DMA seems to stop on rising edge of CS regardless what is declared in...
Hello everyone,
I'm using nRF51822 development kit to do BLE network experiment.
The boards I use are PCA10005 with omnidirectional antenna, and PCA10004 with PCB antenna...
I'm looking at the UICR hardware peripheral example , and trying to figure out the utility in writing to the UICR registers.
Why would I want to modify the compiled hex...
Very new, so please forgive the questions, but...
I have an nrf8001 that I've powered up. After initial power up, I'm able to read the DeviceStartedEvent but the response...
I'm looking to integrate a digital (PDM/I2S) MEMS microphone into my nRF51822-based design. I'd like some pointers to reference designs or other information -- the ones that...
Hi,
I would to know why when the DC/DC is enabled the current is very high (57mA) during RF sending.
Why at the end of RF sending the current is higher than...
