Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
1. I want to put the nrf52832 into deep sleep mode for some amount of time.
2. Once it wakes up from deep sleep mode, will it affect the content of RAM or flash or any system...
This sounds like very n00bie question and I'm a bit embarrassed to ask this, but I'm not getting anywhere so I have to ask it anyway. Why my GPIOTE events are not working...
we have high current consumption when we are using Accelerometer lis3dh with SPI with no transfer at all on SPI
We have 2 SPI’s in the circuit. The first SPI is connecting...
Hi, I am using nRF5832 DK. Currently, I am using SoftDevice s132 to compile my code. I want to compile it with a different SoftDevice (say s112). But it's not working. Kindly...
Hello, We are developing a smart padlock with nRF52840 on Raytac MDBT50Q-1MV2. It will be powered from CR2 type battery. We will support two types of battery chemicals, Lithium...
My minimum requirement is 1568kbit/s .
I try the example that in Nordic\ncs_v1.7.1\v1.7.1\nrf\samples\esb ..
I increased the dynamic load to 252 ,and It can send about...
https://github.com/NordicPlayground/nrf5-calendar-example
I run the above calendar example in nrf52840 and it run successfully with no error or warning, but i did not see...
Hello,
I am using SDK1.5.1 with one nRf5340 as central and another nRf5340 as peripheral. My use case is, I am setting security level 4 (BT_SECURITY_L4) after establishing...
Hi all,
I'm recently working with Nordic devices (more precisely nRF52840), so I'm still learning. I'm working on a project where I have a shared SPI bus with several devices...
I want to open memory window to check the flash area data which has been written when I was debugging with Visual Studio Code but I can NOT find and open the memory window...
Dear DevZone:
I am working with the nRF9160-DK board and I am interested in the following:
1.- Can I implement a VPN communication with this device? 2.- Do I need additional...
Hi,
About the function : nrf_fstorage_write(nrf_fstorage_t const * p_fs,uint32_t dest,void const * p_src,uint32_t len,void * p_param);
I customized an array of data ，but...
I am doing a ble project with three roles exist simultaneously, slave, scanner and broadcaster. i used the 'ble_radio_notification_init' and a rtc to see when the radio is...
Hello Devzone Community,
I'm a couple weeks into learning, working with Nordic ncs, Zephyr RTOS and west and friends. I'm working on an out-of-tree driver, and am stuck...
