I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I've been attempting to install nRF Connect SDK with both the SEGGER Embedded Studio and VS Code IDEs on and off for several months now. These attempts have included automatic...
hi, I have accidentally selected "Erase All" under the Segger Embedded Studio, now my nRF52840 Dongle unable to show its USB port under Windows 10 Device Manager anymore....
Hi,
we are using nrf9160 based custom board with sdk 1.7.0
the issue is when we are sending the data string one by one its works fine, but when we send a string1 and...
Hi, I am using the FDS API to perform operations on flash. What I intend to achieve is: A zero initialised array like data structure in the flash. Initially zeroes are written...
I try to remove and add driver from the Device manager and now in the Device manager I see only two lines 'PPK2' and 'nRF52 Connectivity' and Windows can't install driver...
I want to change the MAC before doing some advertising, they recommended using the ble_gap_addr_set function, but whenever I call the function I get an error and the application...
I've been testing a sample program to log data continuously on a littlefs file system.
I'm using Zephyr OS build v2.6.99-ncs1 and 125 MB (1Gb) NOR flash from Winbond.
...
When utilizing the 2-wire FEM control within the Network core, is it possible to have a 3rd GPIO output slaved to these two FEM control outputs and preserve timing? That is...
Hi Nordic,
I want to use this example to learn bluetooth mesh, but I cannot find the bootloader source code used in this example.
I used vim to view this "serial_nrf52832_xxAA_s132_7_2_0...
Hey, Our custom board based on the reference circuitry in " Product Specification v1.2 ":
We have been using the B0 revision of nRF9160 so far. Now we are planning on switching...
app_twi_perform() returns 0x03 == NRF_ERROR_INTERNAL.
Reset board with button does not help.
After Power Cycle can update EEPROM successfully.
Accessing FTM buffer with...
Hi,
we have developed our working UART code according to Zephyr documentation, and its working fine,
we find that this code works with EasyDMA . but my question is my...
I am trying to scan for Bluetooth LE devices in Android with Java. Everything worked fine and I released an update and on fresh installs it does not work. I went through every...
I'm seeing an assertion failure at PC=0xa806 in nrf52840 + S140 7.3.0, while using L2CAP.
I know the most common cause for softdevice assertion failures is interrupt/timing...
Hi, I'm using nRF52805 and SEGGER. My BLE device disconnects with the mobile app occasionally. The disconnection happens randomly. In the debug mode, I see some messages....
