Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi!
When reading the documentation of the I2S peripheral of the nRF52840, I don't see how to stop the transfer after the last data block. Figure 2 only shows how to start...
Hi,
I used the BLE blinky app on a nRF52832DK and it was working nicely.
I am then trying to make it run on a custom board with nRF52832QFAB version mounted.
I see several...
Hi,
I'm hoping someone can help me get faster throughput when doing DFU in nRF Connect Desktop
I'm using the following hardware / software:
- macOS 12.01
- nRF Connect...
On the nrf52840 I have libuarte working.
The part runs on 1Mbps with 2 timers connected in the define.
This all works great for 90% of the time.
When the incoming data...
Hello I'm curently working on a Project where I'm using the nrf52dk board with the nrf52832.
I wanted to change the dimension of the data transfered with my characteristics...
Hi, sdk:ncs v1.7.0
example path:D:\ncs\v1.7.0\zephyr\samples\subsys\usb\hid-cdc
board :nrf5340dk_nrf5340
DK:PCA10095
How to solve this problem?
Thank you for all...
Hi,
Excuse me. How can I modify cmakelist.exe to display file structure in segger Embedded Studio compiler? Now all files are app/libapp.a below. I have a lot of files now...
Hi, My system has 5 nRF52840 peripherals connected to one central device (PC app).
In the peripheral's sdk_config.h there is a macro NRF_SDH_BLE_PERIPHERAL_LINK_COUNT 1...
If download example light_switch on new clear chip nrf52832, that advertising is not done. But after downloading the firmware without mesh, example light_switch will broadcast...
Hi All,
I am using VS code with nrf Connect Extension and nrf Connect SDK 1.7.0 develop nrf5340 application on windows10.
I created a new application from the Hello World...
I combined the BLE UART and SPIS Peripheral example of SDK V17.0.2 to receive 251 bytes of data from a microcontroller using SPIS protocol. The microcontroller sends data...
Hi,
Peripheral : SDK13, nRF52832
Central : SDK16, nRF52832
It is a phenomenon that occurs in the central device.
I have two questions about the secure connection...
I'm using the latest nRFConnect SDK w/ VSCode with a custom board connected to via a J-LINK. When I look at the call stack it only shows the current thread. I can see thread...
I would like to know when each BLE advertising event has ended for possibility stop after specific number of events and to be able to update advertising data between events...
Hi Dev Zone !
I am actually using nrf52840-dongle for wireless communication with the protocol Enhanced ShockBurst (ESB). I would like to connect an external antenna to...
