Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
We are using nRF9160 and have a rare issue with a very high current consumption from the battery. We are using lithium-thionyl chloride 3,6V batteries, three in parallel....
Hi Everyone! I'm developing a program for NRF52820 that reads the tx power & rssi and makes the calculation for testing different devices, and I've faced some problems while...
Hello Nordic Semi team,
I am building two BLE product. One acts a peripheral and has server capability. Other is central with client capability.
I am trying to understand...
Currently we are integrating the serial and BLE DFU into a single binary executable. The project enables the logging (NRF_LOG_ENABLED = 1) and we use RTT as backend.
When...
i am using VS code, nrf Connect SDK version 1.7.0, (2) nrf 5340 DK boards. Running the CLI example.
uart:~$ ot diag start
failed
error 13 invalid state
uart:~$ ot...
I'm just starting to make a project using SDK 17.1, which is loosely based on a working, mature project based on SDK 15.2 and I'm hitting a bunch of issues. My path here is...
I want to implement an interrupt using TIMER2, but it stops at Dummy_Handler instead of going to TIMER2_IRQHandler.
Is it due to the fact that I have not defined TIMER2_IRQHandler...
This is a pretty top level description of the problem. I've not dug very deep, but what I've observed is that when deployed against an AWS instance set up per the instructions...
Hi, 1-I have successfully developed an app ...\ nRF5SDK17009d13099\nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\ble_app_template. 2-I have set a UART example to send data...
I need to implement a mouse and keyboard (combo) HOG device. There are mouse and keyboard samples, but may I integrate them in just one?
Is there any samplecode?
I have...
To whom it may concern:
We have a product in production based on the nrf52810 and SD 112 ver 6.1.1, developed with SDK 15.3. Due to our manufacturer having nRF52810 availability...
Hello,
I've been trying to access the nRF52840 dongle through the pc-ble-driver-py library. However, I can't get the Nordic examples to run. Here's what I did so far:...
I want to send my sensor data from one node to another node using BLE mesh. my data is at about 128 bytes I am trying to create a custom model but it's hard to know how to...
Hello, I am trying to advertise twice in my project with different gap_params.
First, I have started advertising with the following conn_params (shown below)
#define MIN_CONN_INTERVAL_ADV...
